2015Aae Parts

Bell washer for lawn mowers and tractors. Installs to secure components and prevent loosening. Replace if cracked, worn, or missing for proper assembly.

Secures hoses in your engine to prevent fuel and oil leaks. Replace when rusted or damaged to avoid engine malfunction. Verify fit with your model number.

Replacement fuel tank cap for small engines. Seals the fuel tank to prevent leaks and contamination. Order a new cap if yours is cracked, missing, or worn.

This snap-in bushing provides a low-profile bearing surface to support rotating shafts and reduce wear and noise in appliance assemblies. It restores smooth operation where the original bushing is worn or damaged. What it does:

• Provides a replaceable bearing/sleeve for rotating shafts and posts
• Reduces friction and wear on housing and moving parts
• Helps eliminate rubbing, grinding, or rattling noises during operation
• Maintains correct shaft alignment for smooth rotation

• One snap-in bushing

• Disconnect power before servicing and follow all safety instructions
• Access may require removing panels or covers; inspect surrounding parts for wear
• Press or snap the bushing squarely into the housing until fully seated; avoid deforming it
• Replace any damaged retainers or seals and test operation after reassembly

Replace a worn keeper valve if your small engine has valve train noise or poor compression. This small retaining clip secures valves in lawn mowers and outdoor power equipment.

Engine runs rough or valves aren't opening correctly? This metal valve tappet converts camshaft rotation to linear valve motion. Direct replacement part.

Control wire for lawn and garden engines. Connects controls to engine throttle or choke mechanisms. Replace if frayed, broken, kinked, or missing.

Replacement screw that secures the pawl friction plate in lawn and garden engines. Replaces lost, stripped, or damaged flange bolts on the recoil assembly.

This replacement friction spring is a genuine OEM part meant for any number of small appliance engines run using a starter rope. This spring absorbs large amounts of kinetic energy that could damage the starter rope pulley system. It helps keep the pulley from being overstretched, which would create enough pressure to break the entire system. This spring sits at the center of the pulley system and creates resistance as the user yanks the starter rope. Friction springs can become worn out after repeated use, especially if a user tends to yank the starter rope quite forcefully. The most obvious sign of a worn of friction spring is if the pulley system lacks any resistance. As the user pulls the cord, they should feel a little pull back, but if the friction spring is worn, there will be much less resistance. Replacing this part is straightforward and will only require a screwdriver. Simply open the pulley system, carefully remove the old spring, and install the new one. This part is compatible with a wide number of appliances from Toro, Vanguard, Briggs & Stratton, and Lawnboy. It comes sourced from the original manufacturer and ships individually.

Engine won't shut off when you turn the key? Replace your lawn mower's stop switch to restore safe engine control. Simple safety repair.

E-shaped retainer clip for lawn mowers, snowblowers, and pressure washers. Replace when cracked, broken, or missing to secure engine components.

Crankcase gasket seals cylinder assembly to crankcase. Replace if oil leaks or engine loses compression. Verify fit with your model number.

Engine won't start when you pull the cord? This rewind starter assembly lets you hand-crank your lawn mower engine. Moderate DIY repair for most users.

This genuine OEM part is a rocker switch for lawnmower engines. A rocker switch is the component that allows the user to power the engine. If the rocker switch is no longer functioning and not turning the engine on and off as intended, it might need to be replaced. While replacing a rocker switch may seem like a difficult task, it is actually a simple fix.To replace the rocker switch, pry it off using a flathead screwdriver. Once removed from the mower, unplug the wire harness attached to it. Once unplugged, replace with the new switch. Snap the switch back into its original position and test if it has been installed correctly. If the mower turns on and the engine is able to start, then the installation was a success.This replacement part is sold individually and is compatible with Briggs and Stratton lawnmowers.

Replacement screw for lawn and garden engines. Used to secure components during assembly. Replace if original is lost, stripped, or damaged.

Tap screw for lawn mowers and tractors. Secures panels, guards, and components. Replace if stripped, rusted, or missing to restore proper assembly.