6651329 Parts

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This wire harness connects the appliance's control and power components to restore proper electrical routing and signal transfer. Replace a damaged harness to fix intermittent power, unresponsive controls, or burned/melted wiring concerns. What it does:

• Routes power and control signals between the control board, motors, switches, and sensors
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or no power
• Prevents poor connections that lead to error codes, failed cycles, or component failures
• Restores factory wiring layout for reliable operation and safer electrical paths

• Disconnect power (unplug or switch off breaker) before starting any repair
• Match connector shapes and pin counts; do not force connectors into place
• Route harness along original clips and channels to avoid chafing or heat exposure

This user interface housing secures and protects the oven or range control panel and front electronics, keeping buttons and display aligned for reliable operation and a finished appearance. It restores the control area after damage or wear. What it does:

• Holds the touchpad/display assembly and control board in the correct position for consistent button response
• Shields electronics from spills, grease, and everyday wear that can cause erratic controls
• Restores the front-panel fit and finish to prevent gaps or loose trim
• Helps resolve symptoms such as loose or misaligned buttons, exposed control board, or damaged control-area trim

• One user interface housing (control panel housing) as shown

• Remove power to the appliance before beginning any work to avoid electrical shock
• Basic panel removal and reassembly required; keep screws and clips organized for reinstallation
• If replacing after control-board exposure or liquid damage, inspect the control board and wiring for damage before reassembly
• Use appropriate hand tools and avoid over-tightening fasteners to prevent cracking the housing

This support mounting bracket secures and aligns internal components to keep assemblies stable and operating smoothly. It helps prevent part movement that can cause noise, misalignment, or improper panel fit. What it does:

• Stabilizes and supports adjacent components or panels to reduce vibration and rattling
• Keeps doors or internal assemblies aligned for correct operation
• Prevents shifting that can lead to intermittent contact or wear
• Helps maintain proper spacing where a fixed mount is required

• Disconnect power or unplug the appliance before beginning work
• Handle sharp edges carefully and use the proper screwdriver or nut driver
• Reuse existing fasteners only if they are in good condition; replace stripped or damaged hardware

This push-in retainer secures panels, trim or light-weight components inside the appliance to prevent vibration and movement during operation. It's a small, low-profile fastener that snaps into a pre-drilled hole for a clean, tool-free hold. What it does:

• Holds interior trim, access panels or wiring looms in place to reduce rattles and movement
• Replaces worn or broken plastic retainers that no longer grip securely
• Helps maintain proper alignment of lightweight components for reliable operation
• Can prevent loose parts from contacting moving components

• Disconnect power to the appliance before starting any work
• Access the area and remove any surrounding trim or panels as needed
• Align retainer with the hole and push straight in until it snaps or seats flush
• Inspect fit after installation; replace if damaged or does not secure properly

This air inlet damper controls cold-air flow from the freezer into the refrigerator compartment to help maintain proper fresh-food temperatures. Replacing a faulty damper restores balanced airflow and more consistent cooling. What it does:

• Regulates the amount of cold air entering the fresh-food section from the freezer.
• Opens and closes as the fridge cycles to maintain set temperatures.
• Commonly replaces stuck, broken, or noisy dampers that cause uneven cooling.
• Often used when the refrigerator is warm while the freezer remains cold or when temperatures fluctuate.

• Disconnect power to the appliance before starting any repair.
• Remove interior panels or grille per your model's service instructions to access the damper; keep screws and clips organized.
• Handle plastic fins and actuator gently to avoid damage; do not force the damper into position.
• Reconnect power and verify damper operation and temperature regulation after installation.

This spacer positions and supports the appliance tank/tub assembly to maintain proper alignment and spacing for reliable operation. Replaces a worn or damaged spacer to restore correct fit and reduce movement. What it does:

• Keeps the tank/tub assembly correctly spaced and aligned with the cabinet and mounting points
• Helps prevent rubbing, binding, and excess vibration caused by a missing or damaged spacer
• Restores proper clearance to support seals and hoses that rely on correct tank positioning
• Useful when reassembling the appliance after service or repair

• One spacer

• Disconnect power and water supply before starting any repair
• Access may require removal of outer panels, console, or access covers depending on model
• Handle parts carefully to avoid damaging surrounding seals and wiring; reuse fasteners unless replacement is specified

This replacement silverware basket sits in the dishwasher rack and keeps forks, knives, and spoons upright and contained so they wash thoroughly and don't slip through the rack or interfere with spray-arm movement. What it does:

• Holds and organizes flatware during wash and rinse cycles
• Helps separate utensils for better spray coverage and drainage
• Replaces cracked, warped, or missing baskets

• 1 silverware basket

• Open the dishwasher and pull out the lower rack for access
• Lift out the old basket and place the new basket in the same location/orientation
• Ensure the basket seats securely and does not contact the lower spray arm
• Manually spin the spray arm to confirm clearance before running a cycle

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This thermostat bracket secures the refrigerator/freezer temperature sensor or thermostat to the cabinet, keeping the sensor in the correct position for accurate temperature control. Durable replacement for factory mounting hardware. What it does:

• Holds the thermostat/temperature sensor in place so it reads interior temperatures correctly
• Helps prevent loose or misaligned sensors that can cause irregular cooling or cycling
• Restores proper sensor positioning after damage or broken mounting clips
• Works with the thermostat assembly to maintain consistent appliance operation

• One thermostat mounting bracket

• Disconnect power to the appliance before service to avoid electrical shock
• Handle thermostat/sensor elements carefully; avoid bending or pinching the sensing tube
• Retain or reuse original fasteners unless replacement hardware is explicitly included

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice

The Diverter Motor is an OEM part for Whirlpool dishwashers controls the diverter valve, which directs water flow to various spray arms throughout the dishwasher during a wash cycle. By accurately adjusting the flow of water, the diverter motor ensures that dishes are thoroughly cleaned and rinsed by optimizing coverage and water intensity according to the cycle selected.

Causes of a bad Diverter Motor can include electrical failures, mechanical wear over time, or damage from water infiltration.  

Symptoms of a bad Diverter Motor include:

• Dishes not being cleaned properly due to insufficient water reaching all areas.
• Unusual noises coming from the dishwasher, which may indicate a struggling or stuck diverter motor.
• Error codes displayed on the dishwasher that are related to water distribution functions.
• Leakage from the dishwasher base 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.