Ddbb363 Parts

Secures the upper spray arm so it spins freely and stays aligned. Replace if cracked, worn, or causing wobble to restore proper water distribution.

Secures the upper rack rail to prevent it from sliding out. Replace if missing, broken, or popped off. Installs on the end of the rack track.

Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.

Secures your dishwasher to surrounding cabinetry. Replace this bracket if it's bent, broken, or missing to restore a tight, level installation.

Replacement screw for securing dishwasher door panels, inner liners, and internal brackets. Needed when original screws are stripped, missing, or damaged.

Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.

This flexible injector hose routes liquid between the appliance's injector/dispenser and the pump or spray assembly, restoring proper dispensing and preventing leaks. It's a direct-replacement service part for affected injector connections. What it does

• Carries water or detergent solution from the injector/dispenser to the pump or spray assembly
• Restores normal dispensing when the original hose is cracked, split, or clogged
• Prevents leaks that can cause puddling or improper wash cycles
• Helps restore consistent flow so detergent and rinse/cleaning agents reach the tub

• One injector hose

• Disconnect power and shut off the water supply before starting
• Remove the old hose and reuse or replace any clamps or fittings as needed; install the new hose onto the same connection points
• After installation, restore power/water and run a short cycle to check for leaks and correct dispensing

Replace your dishwasher's spring adjustment bracket if cracked, bent, or missing. This structural component secures the spring mechanism inside your unit.

O-ring seal for dishwasher turbidity sensor. Replace if you notice leaking around the sensor or water pooling inside the dishwasher. Confirm fit with model.

8-32 x 3/8" machine screw secures dishwasher control panels, brackets, and interior assemblies. Replace missing, stripped, or lost screws during repairs.

Bracket that secures the dishwasher door hinge assembly. Installs on the side of the tub. Replace if cracked, bowing outward, or damaged.

This little door seal goes on the corner of the dishwasher door. There are two of these seals - one in each corner. It is recommended to order and replace both. If you need pushnuts, order 99002756.

This control board housing secures and protects the washer's electronic control board, keeping circuitry stable and shielded from moisture and debris for reliable operation. It fits into the console area and supports proper control panel alignment. What it does:

• Holds and protects the electronic control board inside the console from impact, dust and moisture.
• Keeps the control board properly positioned for reliable electrical connections.
• Helps prevent control panel wobble or misalignment that can cause button or dial issues.
• Commonly replaced when housing is cracked, broken mounting tabs fail, or board access is needed.

• 1 control board housing

• Disconnect power and water to the appliance before beginning any repair.
• Handle the control board and housing carefully to avoid damage to connectors or circuit components.
• Use appropriate tools to remove console components; replace damaged mounting tabs and secure all fasteners.
• Discharge any capacitors and follow the board manufacturer's ESD/safety recommendations.

Fix loud chattering noise and food particles left on dishes. This dishwasher chopper assembly restores proper grinding. Moderate DIY repair.

This manifold mounting bracket secures the gas manifold assembly to the appliance frame, keeping fuel lines and related components aligned for reliable operation. It's a direct-fit replacement that restores proper manifold support. What it does:

• Holds the gas manifold in the correct position to prevent strain on connections and lines
• Helps maintain stable alignment of valves and supply tubing to reduce leaks and intermittent flow
• Addresses symptoms like a loose or rattling manifold assembly or visible bracket damage
• Restores proper mounting after impact or corrosion-related bracket failure

• One manifold mounting bracket

• Install only with the appliance powered off and gas supply completely shut; follow local codes
• Match bracket orientation to the original and secure with manufacturer-specified fasteners
• Inspect nearby tubing, fittings and valve mounts for damage when replacing the bracket