Dwhd64cp Parts

Structural support hinge for your dishwasher door. Installs on the side panel to allow smooth opening and closing. Replace if cracked or broken.

Dishwasher door won't stay closed or latch properly? This door latch securely fastens the door during wash cycles. Common DIY fix for door issues.

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

This dishwasher door seal fits into the channel around the tub opening to create a tight, water-resistant barrier when the door closes. Replacing a worn seal helps stop leaks at the front of the unit and keeps cycles running efficiently. What it does:

• Forms a watertight perimeter seal between the tub and door
• Helps contain water and steam during wash and rinse cycles
• Aids proper door compression for reliable closing
• Common symptoms: water on the floor at the front, drips from door corners, visible cracks/flattening, or gaps in the gasket

• 1 door seal

• Disconnect power and turn off water supply before servicing
• Remove the old seal and clean the gasket channel thoroughly
• Start at the top center and press the new seal evenly into the groove without stretching
• Close the door to check for uniform compression, then run a short test cycle to inspect for leaks

This hinge cover is a molded trim piece that protects and conceals a refrigerator door hinge for a clean finished look. It helps keep hinge hardware free of dust and reduces sharp edges while restoring appearance. What it does

• Covers the door hinge area to hide hardware and improve the appliance's appearance
• Helps block dust and debris from accumulating on hinge components
• Reduces the risk of clothes or fingers catching on exposed hinge parts
• Matches OEM fit and shape to maintain proper clearance and alignment

• One hinge cover

• High-level replacement: remove the old cover and snap or screw the new cover into place (specific fasteners vary by model)
• Use basic hand tools if required; for model-specific instructions
• Disconnect power (or follow appliance-specific safety steps) before working near electrical components
• Inspect hinge and hardware while replacing the cover; replace damaged hinge components as needed

Dishrack adjuster regulator with O-ring for dishwashers. Installs on rack assembly to control height adjustment. Replace if cracked, broken, or worn.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Captures small food particles and debris to protect your dishwasher pump and prevent clogs. Replace when clogged or damaged. Verify fit with your model.

Replacement dishwasher water tube channels water between components. Replace if cracked, clogged, or leaking. Confirm fit with your model number.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.

If your dishwasher detergent dispenser won't open during the wash cycle, this actuator lever assembly with springs restores mechanical movement.

Replacement shaft that secures and guides the dishwasher float for accurate water level detection. Needed when the original shaft is worn or broken.