Fcrg3083ada Parts

This factory-assembled door restores a secure, proper closure on your appliance. Replace a damaged, bent, or non-latching door to bring back safe operation and a clean, factory fit.

• Provides the complete hinged door structure that closes and latches the appliance
• Ensures proper engagement of door switches/latches so the unit operates only when closed
• Maintains correct alignment around the opening for reliable performance
• Replace if the door is cracked, warped, misaligned, won't close or stay shut, or the unit doesn't recognize the door is closed

• Disconnect power before servicing; wear cut-resistant gloves to handle edges
• Support the door during removal/installation; use a second person for larger/heavier doors
• Transfer any model-specific hardware (hinges, screws, trim) from the original door as required
• After installation, check alignment and latch operation; adjust per service information if needed

This temperature-sensing probe measures internal appliance temperature and sends readings to the control board so the unit can maintain correct cooling or defrost cycles. Replaces a failed or damaged probe to restore temperature feedback. What it does

• Detects internal temperature and relays it to the control board for accurate cooling and defrost control
• Can cause temperature drift, excessive run times, or failed defrost cycles when faulty
• May trigger temperature-related error codes or cause food to become too warm or too cold
• Works as the control system's feedback element; compatible with the original connector style

• Disconnect power before installing to avoid shock or damage
• Handle the sensor tip and wiring gently; avoid kinking or pulling the lead
• Ensure the connector is fully seated and routed away from moving parts or heating elements

This replacement cap covers and protects exposed fasteners and trim on compatible Frigidaire appliances, restoring a finished appearance while helping keep out dirt and moisture. A simple, low-cost part for cosmetic and protective repair. What it does:

• Covers exposed fasteners, hinge posts, or trim edges to restore the appliance's finished look
• Helps prevent dirt, debris and moisture from entering mounting points and seams
• Can reduce rattling or vibration caused by missing or damaged trim pieces
• Snaps or presses into place to conceal hardware without altering function

• Typically installs by snapping into position; no special tools usually required
• Work with the appliance powered off if accessing areas near electrical components
• Inspect mating surfaces for damage or debris before installing for a secure fit
• Replace with identical OEM cap for correct fit and appearance

This power cord supplies electrical power to the appliance, restoring a safe, factory-style connection between the outlet and the unit. Use it to replace a damaged or worn lead to regain reliable power. What it does:

• Replaces a worn, frayed or damaged power lead to stop intermittent power or visible cord damage
• Restores a secure electrical connection when the original cord is cut, melted or has exposed wires
• Helps eliminate power-related failures caused by broken conductors or loose cord terminals
• Works as the external mains connection between the appliance and household power

• One power cord

• Always unplug the appliance or switch off house power at the breaker before replacing the cord
• Verify the cord's terminal type and wire count match your appliance before installation
• Tighten terminal connections to the manufacturer's specified torque and secure strain relief where provided

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker so you get a steady supply when needed and stop unwanted leaks. Replaces a worn or faulty valve to restore proper fill and dispensing. What it does

• Opens and closes to allow water into the ice maker and dispenser when requested
• Stops water flow to prevent overfilling or continuous running
• Commonly replaced when dispenser or ice maker won't fill, has weak flow, or leaks
• Works with the refrigerator's water line and solenoid actuators to meter supply

• One water inlet valve (single unit as shown)

• Disconnect power and shut off the household water supply before starting
• Drain lines and remove front or rear access panels to reach the valve
• Inspect and replace any damaged water lines or fittings; tighten connections and check for leaks after installation

This door gasket is a direct-replacement refrigerator door seal that helps maintain an airtight closure to keep cold air in and reduce energy loss. It restores proper sealing around the door for more consistent internal temperatures. What it does:

• Forms a tight seal around the refrigerator door to help prevent warm air intrusion and frost buildup
• Helps maintain consistent internal temperatures for better food preservation
• Reduces compressor run time caused by a leaking door seal
• Addresses common symptoms like visible gaps, cold air loss, or condensation at the door edge

• One replacement refrigerator door gasket

• Turn off power to the appliance and empty the door prior to replacing the gasket
• Remove the old gasket carefully to avoid damage to the door finish or mounting channel
• Warm and flex the new gasket as needed for easier installation and to help the gasket seat properly

This ignitor/orifice is the replacement part for the oven's gas burner ignition assembly, helping the burner light reliably so your oven can reach and hold cooking temperature. Designed to restore proper ignition function. What it does:

• Provides the ignition pathway and orifice for the oven burner so gas can be lit safely
• Restores consistent ignition when the burner fails to light or lights intermittently
• Can stop clicking or sparking without ignition when the orifice or ignitor is compromised
• Helps produce an appropriate pilot/ignition spark for stable burner operation

• Turn off gas supply and power to the appliance before starting any service
• Inspect surrounding gaskets and fittings for leaks or damage when replacing the part
• Hand-tighten fittings and follow torque guidance from the oven's service manual where applicable

This water inlet valve controls the flow of water into the refrigerator for the dispenser and ice maker, restoring reliable water delivery and proper ice production when the valve fails. Designed to match OEM fit and function. What it does:

• Opens and closes to let water into the ice maker and water dispenser when activated
• Stops water flow to prevent leaks when the refrigerator is off or not calling for water
• Commonly replaced for symptoms like no water at the dispenser, slow water flow, or no ice production
• Works with the refrigerator's solenoid control to regulate water delivery

• One water inlet valve assembly

• Disconnect power and shut off the home water supply before starting any repair
• Inspect water lines and fittings for damage; replace damaged lines to prevent leaks
• Mounts in the refrigerator base or rear per the OEM configuration; use original hardware where possible