Ffss2615ts2 Parts

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Refrigerator not cooling or freezing properly? A faulty evaporator coil may be causing warm temps and moisture buildup. Professional installation recommended.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

White plastic hinge cover that snaps onto your refrigerator door hinge. Replace if cracked, broken, or discolored to restore a clean appearance.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

Limits refrigerator door swing to prevent over-extension. Replace if broken, cracked, or missing to restore proper door alignment and protect hinges.

Creates an airtight seal around your refrigerator door to keep cold air in and prevent frost buildup. Replace if torn, cracked, or loose. Confirm fit.

Replace a cracked or broken refrigerator cover. This cosmetic part installs to conceal internal components and maintain a clean appearance.

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

This cover hinge secures and supports the appliance's top or access panel, restoring smooth opening and stable positioning. It replaces a cracked, broken, or worn hinge so the cover stays aligned and operates reliably. What it does:

• Provides a pivot point for the top/access cover so it opens and closes correctly
• Keeps the cover aligned to prevent gaps or rubbing against adjacent panels
• Replaces broken or cracked hinges that cause the cover to droop or sit uneven
• Eliminates loose, wobbly, or noisy movement when lifting the cover

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools; keep fasteners and small parts organized during removal
• Handle panels carefully to avoid scratches; support the cover while removing/installing the hinge

Left hand side. For the right hand side order 241674402

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Secures refrigerator hoses to fittings with spring tension to prevent leaks. Replace when clamp loses grip or shows rust. Verify fit with model number.

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components