Ffss2615ts2 Parts

This spring solenoid is the actuator spring assembly that helps move and return a solenoid-driven mechanism, restoring reliable part movement and engagement in affected appliance systems. What it does:

• Provides return tension and controlled movement for a solenoid actuator
• Helps the solenoid plunger snap back after activation so linked components reset
• Commonly replaced when the actuator fails to move, sticks, or does not fully return
• Corrects symptoms such as intermittent engagement, sticking, or loss of actuator motion

• Disconnect power to the appliance before attempting service to avoid shock or injury
• Handle small components carefully; keep track of retaining clips, pins, or fasteners
• Replace with the exact part number to ensure fit and function
• Refer to OEM instructions for step-by-step removal and reassembly

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This control rod bracket secures the control rod to the appliance, restoring proper linkage and part alignment for reliable operation. Designed to replace a worn or broken mounting bracket and stabilize control movement. What it does:

• Holds the control rod in place so levers and linkages operate smoothly
• Restores proper alignment when the rod is loose, bent, or detached
• Helps eliminate binding or intermittent actuator movement caused by a damaged bracket
• Supports consistent mechanical operation of the connected control components

• One control rod mounting bracket

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Remove any panels or covers as needed to access the bracket; keep fasteners organized for reassembly
• Inspect adjacent linkage and fasteners; replace any damaged clips or screws for a secure fit

A replacement fixed round blade that restores the appliance's original blade function and helps reduce vibration, noise or uneven performance caused by a worn or damaged blade. Use this OEM component for a proper fit and reliable operation. What it does

• Replaces a worn, bent or damaged fixed round blade to restore intended blade performance.
• Restores balance and smooth operation to the rotating assembly.
• Can reduce noise, wobble or uneven operation associated with a damaged blade.
• Matches OEM fit and function to help ensure correct alignment.

• Disconnect power to the appliance before beginning any work.
• Handle blade edges carefully; wear cut-resistant gloves if available.
• Remove and install per the appliance service manual or OEM instructions.

This trough drain channels defrost and condensation water from the evaporator area to the refrigerator drain pan, helping prevent pooling and ice buildup. Fits as the replacement evaporator-area drain trough in compatible refrigerators. What it does:

• Collects and directs defrost/condensation water away from the evaporator compartment
• Helps prevent water pooling inside the fresh food or freezer section
• Reduces ice formation around the evaporator area when functioning properly
• Works with the drain tube and pan to route water safely to the drain pan

• One trough drain

• Disconnect power to the appliance before starting any service
• Remove interior shelves, drawers, and the evaporator cover to access the trough
• Inspect surrounding seals and the drain tube for clogs; clear any debris before installing
• Reassemble panels and restore power; run a short defrost cycle or pour warm water to verify proper drainage

This small mounting clip secures interior or cabinet components to keep panels and trim stable, helping reduce noise and maintain proper alignment. It's a simple replacement that restores a snug fit where the original clip has broken or worn. What it does:

• Holds panels, trim, or small components in place to prevent gaps or rattling
• Restores proper alignment of clipped parts after damage or wear
• Maintains a secure attachment point for adjacent parts during normal use
• Helps prevent moisture or debris from entering behind secured panels

• Disconnect power or unplug the appliance before accessing internal components
• Handle the clip and surrounding trim carefully to avoid cracking adjacent plastic
• Use basic hand tools as needed; do not force clips into place—align before snapping
• Replace any damaged mounting features for a secure fit

This control rod is a direct-replacement linkage rod that connects a user control to the appliance's internal mechanism, restoring reliable mechanical movement and control operation. What it does:

• Transfers motion from an external control lever or knob to the internal mechanism
• Replaces a bent, worn, or broken linkage that causes sticky or non-responsive controls
• Helps restore proper engagement and consistent mechanical action
• Works as a simple mechanical replacement—no electronic programming required

• One control rod

• Disconnect power (and gas if applicable) before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Handle small parts carefully to avoid damage and ensure proper alignment during reassembly

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This channel-shelf mounting piece secures a refrigerator shelf in its track, keeping shelves stable and aligned for safe storage. Fits into the shelf track to support glass or wire shelves and prevent shifting during use. What it does:

• Provides a secure track for sliding or fixed refrigerator shelves
• Holds shelf edges level to prevent items from tipping or falling
• Helps maintain proper shelf spacing and alignment inside the cabinet
• Commonly replaced when the shelf no longer seats or the channel is cracked or bent

• Use basic hand tools; remove the shelf before removing or installing the channel
• Inspect adjacent clips and shelf supports for wear and replace if needed
• Handle glass shelves carefully to avoid breakage during installation

This is a door assembly for refrigerators. It is the part of the refrigerator that allows a user to open and close the appliance. It's located on the front of the refrigerator and is made of durable materials. If the door assembly is causing problems with appliance function, it will need to be replaced.When replacing the door assembly, the refrigerator should be unplugged or the circuit breaker should be turned off. A set of tools will be needed to replace this part with a new component. Unthread the screws on the door hinges and remove the covers. Have a helper support the door as it is removed. If included, the water dispenser should be disconnected. Disconnect the wires over the freezer door hinge. Next, install the new door assembly and attach all wires and components before turning the power back on.This component is sold on an individual basis. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The door assembly is designed to be compatible with several Frigidaire refrigerators.