Fgid246qf2a Parts

This replacement door gasket creates a tight seal around the refrigerator door to help maintain proper temperature and reduce energy loss. It restores the seal where the original gasket is torn, warped, or no longer sealing. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and uneven cooling in the compartment
• Reduces energy use caused by a failing door seal
• Commonly used when the existing gasket is cracked, stretched, or no longer sealing

• Remove power to the appliance before starting any work
• Clean the door mating surface thoroughly before installing the new gasket
• Press the gasket into the door channel, starting at the top and working around the perimeter for an even fit
• If necessary, warm the gasket gently (per OEM guidance) to help it seat; avoid open flames or excessive heat

This display assembly replaces the fridge's front control console to restore temperature readouts and touch/selector feedback. It gives clear visual status and lets you change settings from the appliance's exterior control panel. What it does:

• Replaces a cracked, unresponsive, or blank front display/console
• Restores on-screen temperature, mode indicators and user-input feedback
• Helps resolve intermittent or non-functioning touch buttons or LEDs
• Works as the visible interface between you and the refrigerator's control system

• Disconnect power to the appliance before starting any repairs to avoid shock or damage.
• Removal usually requires panel screws and careful disconnect of wiring harness(es); handle the display with care to avoid scratches.
• Verify connector orientation before reassembly; do not force connectors.

This hose clamp secures flexible water or drain hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal and helps stop drips or loose hoses. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to prevent leaks
• Restores a tight connection when original clamp is corroded, bent, or broken
• Helps eliminate water dripping, puddling, or intermittent leaks at hose joints
• Prevents hoses from slipping off during vibration or normal appliance use

• Disconnect power and shut off water supply before starting any repair
• Tighten clamp securely with pliers or the appropriate tool; avoid over-tightening which can damage the hose
• After installation, restore water and power, then check the connection for leaks

This is a genuine replacement mounting screw used to secure components in compatible Frigidaire appliances. It restores proper fastening so panels and parts stay aligned and stable during normal operation. What it does:

• Fastens appliance components, panels, or brackets to maintain secure assembly
• Replaces worn, stripped, or missing screws that cause rattling or loose parts
• Helps eliminate vibration-related noise by restoring correct fastening
• Matches OEM fit and function for reliable, long-lasting hold

• One replacement mounting screw, as pictured

• Use the proper size driver to avoid stripping the head; tighten until snug but do not overtighten
• Match screw location and length to the original for correct fit; keep any removed hardware for reference
• Disconnect power to the appliance before working in internal areas to reduce shock risk

This is a replacement screw used to secure appliance panels and components, restoring proper fit and stopping looseness or rattling. It's a direct-fit fastener that helps maintain safe, stable operation when original hardware is missing or worn. What it does

• Secures panels, brackets, trim pieces or internal components in place
• Stops rattling or vibration caused by loose fasteners
• Helps maintain proper alignment of parts for reliable operation
• Restores missing or damaged mounting hardware

• Screw

• Disconnect power (and water if applicable) before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or parts
• Keep removed hardware organized before final assembly

This display assembly is the user-facing control panel that shows settings and status for your appliance, restoring clear indicator lights and touch/selection feedback so you can set cycles and monitor operation. What it does:

• Replaces the appliance's front display and indicator interface so controls and status lights are visible
• Restores readable cycle, temperature, and error indicators that may be blank or dim
• Helps resolve symptoms like unlit or unresponsive display, missing icons, or incorrect status readouts
• Works with the existing user interface and button mechanisms when mechanically compatible

• High-level replacement: remove the control housing or fascia to access the display assembly; follow manufacturer service instructions
• Disconnect power (unplug or shut off breaker) before starting work to avoid shock or damage
• Handle the display and ribbon/connectors carefully to avoid bending or damaging contacts

No.7 plastic .375

This wiring harness is an electrical connector assembly that routes power and signals between components to restore reliable appliance operation. It replaces damaged or worn wiring to help re-establish secure electrical connections. What it does:

• Connects power and control signals between internal components to enable normal appliance functions
• Replaces frayed, melted, or broken wires that can cause intermittent operation or failure to start
• Helps resolve flickering controls, loss of power to parts, or unreliable component response
• Maintains correct routing and connector fit to prevent shorts and poor connections

• One wiring harness assembly

• Disconnect all power to the appliance before starting any repairs to avoid shock or injury
• Verify connector orientation and secure all terminal connections; do not force connectors into place
• Route the harness to match factory wiring paths and use existing clips or tie points to prevent rubbing

These are replacement countertop mounting screws that secure the appliance to the countertop or cabinet, restoring a stable, flush fit and preventing movement or gaps. Sold as a 2-pack for quick, direct replacement. What it does

• Secures the appliance countertop or trim to the cabinet or counter to keep the unit from shifting.
• Helps eliminate rocking, gaps, or uneven alignment caused by missing or loose mounting screws.
• Restores proper fit and finish where original mounting hardware has been lost or damaged.
• Works with factory mounting points and standard driver heads for straightforward replacement.

• Two countertop mounting screws.

• Use the correct-size driver to avoid stripping the screw head.
• Tighten until snug; avoid over-tightening which can strip threads or damage the cabinet/countertop.
• Keep original brackets and hardware; replace only the missing or damaged screws as needed.

This is a genuine replacement mounting screw used to secure appliance panels and components. It restores proper fit and helps prevent rattling or loose parts for safe, reliable operation. What it does:

• Fastens panels, trim pieces, or internal components to maintain proper alignment
• Secures parts that can vibrate or become loose during normal use
• Helps stop rattling, squeaks, or gaps caused by missing or damaged fasteners
• Suitable wherever the OEM specifies part 154041001 as the required screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screw hole and match thread engagement; do not force or cross-thread
• Tighten firmly but avoid over-torquing to prevent stripped threads or cracked panels
• If multiple or different screws were removed, keep track of each location for correct reassembly

This sump retainer secures the appliance sump assembly and helps keep the pump seal and surrounding components properly positioned to reduce leaks and maintain correct water flow. It's a small replacement part used during sump or pump repairs. What it does:

• Holds the sump housing or pump assembly in place to maintain a reliable seal
• Helps prevent water leaks from the pump/sump area when installed correctly
• Keeps internal components aligned for proper water circulation and drainage
• Commonly replaced when sump hardware is cracked, warped, or no longer secures the pump

• One sump retainer

• Power off and unplug the appliance before starting any repair
• Verify you have full access to the sump/pump area; removal of panels or racks may be required
• Inspect surrounding seals and gaskets; replace if damaged to ensure a watertight fit

A replacement switch mounting screw that secures control switches and switch assemblies in place for reliable operation. Replaces lost or stripped mounting hardware to restore secure panel and switch attachment on compatible appliances. What it does:

• Fastens the switch or switch bracket to the appliance frame or control panel
• Keeps electrical switch connections stable to prevent intermittent contact or movement
• Helps eliminate loose or rattling switches and noisy control panels
• Restores proper alignment of the switch for reliable user control

• Turn off power to the appliance before accessing the control panel to avoid shock
• Use the matching screwdriver size to avoid stripping the screw head
• Tighten securely but do not over-torque to prevent damage to the switch or panel
• Replace all affected fasteners for a secure fit