Flce7522aw4 Parts

This limit switch is a safety cutoff switch used in household appliances to stop operation when a fault condition is detected, helping protect the appliance from overheating or unsafe operation. It replaces a failed or intermittent switch to restore normal safety control. What it does:

• Acts as a thermal/safety cutoff or interrupt point in the appliance control circuit
• Opens the circuit when temperature or fault conditions exceed safe limits
• Can cause symptoms such as no heat, intermittent heating, or an appliance that won't complete cycles when it fails
• Restores proper safety sensing when replaced with a matching part

• Disconnect power to the appliance before inspecting or replacing the switch.
• Handle terminals and wiring carefully; ensure secure connections and correct orientation.

This hose/wire clamp secures appliance hoses or wiring to prevent rubbing, chafing and unwanted movement—helping reduce leaks, shorts, and noise from loose lines. Simple, small replacement that restores proper routing and retention. What it does:

• Holds a drain hose, water line or wiring bundle in place at attachment points
• Prevents hoses or wires from rubbing against sharp edges or moving parts
• Reduces risk of leaks, electrical chafing, rubbing noise, and vibration-related wear
• Fits into a mounting tab or hole and snaps or tightens to retain the line

• Disconnect power and shut off water before accessing plumbing or wiring
• Inspect nearby hoses/wires and mounting tabs; replace if damaged
• Position clamp over the hose or bundle and engage onto the mounting tab until secure
• Use appropriate pliers if needed; avoid over-tightening or deforming the hose

This vane is an air flow deflector that helps direct cold air inside the refrigerator compartment for more even cooling. It replaces a worn or broken vane to restore proper airflow routing and reduce temperature differences. What it does:

• Directs cold air from the evaporator or duct into the fresh food compartment for balanced cooling
• Helps maintain consistent temperatures across shelves by guiding airflow
• Can prevent blocked airflow caused by a cracked or missing vane
• May reduce noisy airflow caused by a loose or damaged deflector

• One vane/air flow deflector

• High-level replacement; turn off power to the appliance before starting
• Inspect surrounding clips or mounting tabs and replace if damaged
• Handle gently to avoid cracking plastic tabs during installation

This flat washer provides a secure, low-profile spacer between mating parts in the washer assembly to prevent loosening and reduce wear. It restores proper fit and alignment for quieter, more reliable operation. What it does:

• Acts as a spacer and load distributor between fasteners and components
• Helps maintain proper alignment of moving parts to reduce vibration and noise
• Prevents metal-on-metal wear where used in the assembly
• Commonly replaced when worn, bent, or corroded causes looseness or rattling

• Turn off power and water supply to the appliance before beginning any repair
• Replace only with the exact washer size and thickness specified for your model
• Keep hardware and surrounding parts clean; inspect for related wear or damage

This wiring harness connects the refrigerator's control board to key components, restoring reliable electrical pathways so fans, lights, and ice/water systems receive proper signals. Use it to replace damaged or burned wiring that causes intermittent or no operation. What it does

• Routes power and control signals between the control board and components.
• Replaces cracked, frayed, or heat-damaged wires that can cause intermittent operation or component failure.
• Helps resolve symptoms such as lights or fans not running, no ice/water operation, or loss of control communication.
• Restores factory wiring configurations and secure connector fit.

• One complete wiring harness as shown.

• Disconnect power to the appliance before beginning work to avoid shock or damage.
• Verify connectors match and seat fully; do not force connectors into place.
• Route and secure the harness along factory paths; use existing clips and retainers when present.
• Inspect surrounding components for heat or damage that could have caused the harness failure.

This wiring harness connects the oven's control board to its components, restoring reliable electrical connections and helping the range operate correctly. Use it to replace damaged, burnt, or loose harnesses that cause intermittent or no power to controls. What it does

• Transfers power and signals between the control board and oven components (controls, sensors, igniter).
• Replaces harnesses with damaged insulation, broken wires, or corroded terminals.
• Can stop intermittent control failures, erratic operation, or loss of specific functions tied to a disconnected circuit.
• Maintains factory routing and connector fit for secure, reliable connections.

• Always disconnect power (unplug or shut off breaker) before servicing electrical components.
• Route harness along original clips and channels to avoid heat or pinch points.
• If terminals are corroded or other components are damaged, inspect and replace them as needed.

This replacement knob assembly restores proper control of your appliance's settings by replacing a cracked, loose, or non-turning control knob. It provides a secure fit so you can select temperatures and cycles reliably. What it does:

• Replaces a worn, cracked, or broken control knob so settings can be selected and adjusted
• Pushes onto the control shaft and holds steady to prevent slipping during use
• Restores clear tactile feedback and accurate positioning for temperature or function selection
• Helps eliminate issues like a knob that won't turn, spins freely, or has missing pieces

• Disconnect power (and gas if applicable) before starting any repair
• Pull off the old knob straight from the control shaft; inspect shaft for damage before installing
• Align splines on the replacement knob with the control shaft and push it fully into place
• After installation, restore power and cycle through settings to ensure secure fit and correct operation