Fpm0209kf Parts

This replacement lever is the small actuator that engages control linkages so doors, latches or dispenser mechanisms move and stay in position. Replacing a worn or broken lever restores reliable mechanical operation and alignment. What it does:

• Transfers motion from a handle or control cam to the linked mechanism
• Helps door/latch/dispenser engage and stay in the correct position
• A damaged or cracked lever can cause sticking, poor latching, or intermittent operation
• Commonly fails from wear, impact, or plastic fatigue

• Disconnect power to the appliance before beginning work to avoid injury
• Removal typically requires basic hand tools; keep fasteners for reuse
• Handle small plastic parts carefully to avoid damage during installation
• Test the mechanism through a full cycle after installation to ensure proper engagement

Wire harness for microwaves. Connects electrical components inside the unit. Replace if wires are frayed, connectors are damaged, or harness is melted.

Illuminates the interior of your microwave or cooking surface below. Replace when bulb burns out or flickers. Verify compatibility with your model.

Vent adapter assembly installs in the oven cavity to connect ventilation ducts. Replace if cracked, damaged, or missing to restore proper airflow.

This Tube Assembly routes water inside the refrigerator to the dispenser and ice-maker, restoring proper water flow and preventing leaks when the original line is damaged. Reliable replacement for delivery and fill connections. What it does:

• Transports water from the inlet to the ice maker/dispenser assembly
• Replaces cracked, kinked, or leaking tubing that causes puddles or low water flow
• Helps restore normal ice production and dispenser operation when the tube is the fault
• Matches OEM routing and connector types for correct fit and seal

• One tube assembly as shown

• Disconnect power and shut off the water supply before starting
• Remove ice maker or access panel as needed to reach routing; follow OEM service instructions
• Inspect fittings and replace any damaged clamps or seals; avoid kinking the new tube
• After installation, turn on water, check for leaks, and run dispenser/ice cycles to confirm proper flow

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

Fix a microwave door that won't close properly or latch mechanism that's loose. This tension spring restores proper movement to internal components.

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

Fix an oven that won't heat, has a blank display, or shows error codes with this electronic control board. Restores proper temperature control and functions.

This door assembly replaces a damaged or dented refrigerator door to restore a proper seal and appearance. It mounts in place of the original outer door panel and helps the appliance maintain temperature and efficiency. What it does:

• Replaces a cracked, dented or warped refrigerator door outer panel.
• Restores correct door alignment and helps the gasket seal against the cabinet.
• Reduces air leaks that can cause temperature fluctuations or increased run time.
• Returns the refrigerator to a finished, uniform exterior appearance.

• Handle, trim, gasket, or hinge hardware may need to be transferred from the old door—verify contents before install.
• Disconnect power and empty door contents before removing the old door to avoid injury or damage.
• Use appropriate tools and support the door while removing or installing to prevent drops.

This door gasket creates an airtight seal around the refrigerator door to help maintain proper temperature and prevent moisture and frost buildup. Replacing a worn seal restores consistent cooling and reduces energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm, humid air out
• Helps prevent frost accumulation and moisture on interior surfaces
• Restores proper temperature control when the original seal is cracked, torn, or compressed
• Reduces energy waste caused by a leaking door seal

• One replacement door gasket

• Unplug the refrigerator or disconnect power before beginning work
• Clean the gasket channel and door surface before installing the new seal
• Press the gasket evenly into the door channel; warm water or a hair dryer on low can help make the gasket more pliable for a tight fit
• Check the door alignment and close the door several times to seat the gasket; avoid using sharp tools that could damage the seal

Front console fascia panel for your microwave that houses control buttons and display. Replace if cracked, broken, or worn to restore appearance.

This electronic control panel is the front user interface that lets you set and monitor oven functions, temperature and timers for your range or wall oven. It restores button control and display feedback so the appliance responds correctly to settings. What it does:

• Replaces a cracked, burnt or non-responsive control panel to restore user input and display functions
• Returns control over bake, broil, timer and clock settings when buttons or touchpads fail
• Fixes symptoms such as unresponsive keys, blank or flickering display, or intermittent control behavior
• Works as the main interface between the user and the oven's electronic control

• One control panel user interface assembly

• Disconnect electrical power to the appliance at the breaker before starting
• Handle display and fascia carefully to avoid scratching or cracking glass/plastics
• Basic tools are typically required; alignment and connector seating must be checked during reassembly

Replace your wall oven's internal shield if cracked, broken, or missing. This protective cover shields electrical components from heat and debris.

Replace a cracked, damaged, or missing shield in your wall oven or microwave combo. This protective panel installs behind components to prevent wear.