Gdf535pgr5ww Parts

This dishwasher fill funnel guides water flow into the appropriate channel, helping ensure proper distribution during wash cycles. Replacing a warped or damaged funnel can prevent leaks and restore consistent spray performance.

• Directs water into the dishwasher's internal water feed path
• Helps maintain correct water pressure for spray arms
• Common failure signs: leaking at the funnel area, poor spray performance, residue on dishes, or misalignment with the water feed tube
• Physical damage, warping, or a loose fit are typical replacement indicators

• Disconnect power and turn off water supply before servicing
• Access from inside the tub; remove any retaining screws or clips
• Inspect and reuse existing hardware/seals if still in good condition
• After installation, run a short cycle and check for leaks or misalignment

Replacement fill funnel hose that routes incoming water into the appliance's fill system. Restores proper water flow to the fill inlet and helps stop leaks at the funnel connection when the original hose is cracked or worn. What it does:

• Channels incoming water from the inlet to the appliance fill assembly.
• Replaces cracked, split, or collapsed funnel hoses that can cause leaks.
• Common symptoms it can fix: water leaking at the funnel connection, slow or incomplete fill, water pooling beneath the appliance.
• Simple direct-replacement part—matches the original funnel hose routing and connection points.

• Always disconnect power and shut off the water supply before servicing the appliance.
• Inspect mating fittings, clamps, and seals; replace clamps or seals if corroded or damaged.
• Use basic hand tools to remove and secure hose clamps; avoid twisting or kinking the hose during installation.

The Door Spring is an OEM part for GE dishwashers. It provides proper tension and balance for the dishwasher door. It helps maintain stability during operation, allowing for easy loading and unloading of dishes.

A bad Door Spring can lead to issues such as a loose or sagging dishwasher door, difficulty in opening or closing the door, or the door not staying securely in place. Causes of a bad door spring can include wear and tear over time, exposure to heavy loads or excessive force, or damage due to accidental mishandling.

Symptoms of a bad Door Spring include:

• Loose or sagging dishwasher door
• Difficulty in opening or closing the door 
• Door not staying in place 
• Noises when trying to open or close the door

Replace your worn-out or damaged Door Spring with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This replacement AC wire harness routes power between an appliance's main control and its AC components to restore reliable electrical connections and safe operation. Designed as a direct-fit harness for compatible GE appliances. What it does:

• Provides the factory-style wiring path for AC power and signal connections
• Restores lost or intermittent power caused by damaged or frayed wires
• Replaces burned, corroded, or broken connector ends to improve electrical contact
• Helps stop erratic operation caused by open or shorted harness leads

• One replacement AC wire harness

• Disconnect power to the appliance before starting any repair
• Inspect connectors and routing; replace only if the harness matches OEM connector types
• Secure harness away from sharp edges and moving parts to prevent future damage

The Upper Rack Roller and Stud Assembly is an OEM replacement part for GE dishwashers. Located inside the upper dish rack, this assembly utilizes precision-engineered plastic rollers and support studs to guide rack movement. Reliable rollers and stable rack positioning are key to smooth operation and effective washing. 

Causes of a faulty assembly include worn or cracked rollers, broken or missing support studs, or loss of lubrication after extended use.

Symptoms of a problematic roller and stud assembly include:

• Noisy or grinding sounds were heard from the upper rack area
• Rack that does not glide smoothly or gets stuck during opening/closing  
• Potential damage to rack or componentry from an unsupported rack
• Difficulty loading or positioning dishes securely 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This configured UI control board is the user interface assembly that lets you operate your appliance, restoring the touchpad/display and control functions so settings and cycles respond correctly. What it does:

• Replaces a faulty front control board to restore touchpad and display responsiveness
• Resolves symptoms like unresponsive buttons, blank or erratic display, or controls that won't accept inputs
• Interfaces with the main control to send user commands for oven/range functions
• Used when diagnostics point to a failed or damaged UI/control assembly

• Always disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by its edges and ground yourself to avoid static damage
• Retain screws and connectors; compare the new board to the old one before installation

The Screw is an OEM part for GE dishwashers. This screw is designed for various applications, including securing and fastening components in your GE appliance.

A bad screw can result in issues such as loose or unstable components, improper functioning, or even potential damage to other parts. Causes of a bad screw can include wear and tear over time, improper installation, or exposure to extreme conditions.

Symptoms of a bad Screw include:

• Components becoming loose or detached
• Parts not securely fastened
• Unusual noises or vibrations during operation
• Visible signs of damage or wear on the screw

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower rack roller and stud assembly is an OEM part for GE dishwashers. It supports smooth movement of the lower dish rack in and out of the tub.

Causes of a bad roller and stud assembly can include wear from repeated extension/retraction of the rack. Mineral buildup may also impede smooth operation over time.

Symptoms of a bad roller and stud assembly include:

• Difficulty fully extending or retracting the lower dish rack  
• Noisy squeaking or grinding noises when moving the rack
• Rack that does not glide easily or gets stuck partially out

Replacing the roller and stud assembly with this genuine GE part restores convenient access to dishes on the lower rack. Its quality ball bearings and durable construction enhance usability cycle after cycle.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
 

The Wash Pump Service Kit is an OEM part for GE dishwashers. It works to circulate water within the dishwasher during wash cycles. The kit includes both the wash pump along seal components. 

Causes of a bad wash pump service kit include deterioration of seals and gaskets, debris buildup restricting pump function, or motor failure due to age.

Symptoms include:

• Inadequate or inconsistent water pressure during the wash  
• Drips or leaks from the pump area
• Grinding or humming noises from the pump
• Inability to properly fill or drain water

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Diverter Assembly is an OEM part for GE dishwashers. It is a water flow management component that directs water via internal channels and ports to target specific spray arms and jets during various wash cycles. 

Symptoms of a faulty diverter include:

• Inconsistent or inadequate rinsing  
• Reduced cleaning power on certain sections of dishes
• Odd noises coming from inside the dishwasher 

Causes can be mineral buildup clogging water passages, worn diverter vanes, or cracks in the assembly housing allowing leakage.

Properly replacing with the authentic GE OEM part restores like-performance water distribution. With uniform coverage, all dishes receive thorough cleaning and drying. Compatible with Hotpoint, RCA, and Kenmore models.

The Fine Filter is an OEM part for GE dishwashers. Located at the bottom of the dishwasher tub, the fine filter traps small food particles and debris to prevent clogs in the wash pump and other components. It is a critical filter that helps optimize cleaning performance and protect internal mechanisms.

Symptoms of a bad fine filter include:

• Reduced or inefficient water spraying from the arms  
• Accumulation of debris inside the tub
• Foul odors emitting from the dishwasher
• Drainage or water flow issues 

Over time, particles can accumulate in the fine filter mesh causing it to become clogged. Choosing this genuine GE replacement ensures optimal filtration. It upgrades your dishwasher with a new filter to once again trap particles and keep the wash system running smoothly. This OEM GE part aligns with specifications for Crosley, KitchenAid, and select Kenmore dishwashers as well.
 

The Pulley Cable is an OEM part for GE dishwashers. As a component for proper door operation, the pulley cable works with internal springs to balance the door during opening and closing movements. 

Symptoms of a bad door pulley cable include:

• The door lacks proper closing assistance and slams shut  
• Difficulty opening or requiring extra force to move the door
• Door unable to fully latch or lock into position

Causes can be fractures in wire strands weakening cable strength over thousands of uses. Extreme bends also damage internal wiring over time. 

This OEM part is compatible with select Hotpoint, RCA, and Kenmore models, 

The Plastic Coarse Filter is an OEM replacement part for GE dishwashers. It refers to a screen fitted over the wash impeller that traps soil and food debris. Subject to constant exposure to water and detergents, plastic parts can wear down over many cycles. 

Symptoms of a bad coarse filter include:

• Clogged or blocked mesh no longer prevents large particles from entering the wash arm spray jets  
• Cracks along seams or mounting points where water can seep behind
• Brittle or broken crosspieces within the screen compromising structural integrity

Causes of failure relate to the chemical deterioration of plastic combined with physical stresses as debris repeatedly builds up and then dislodges during high-velocity rinse cycles.

This GE replacement part is also compatible with some Hotpoint and RCA models.

The Rack Roller is an OEM component compatible with GE dishwashers. Located on the rack guide rails inside the washer tub, it facilitates smooth gliding of rack shelving in and out for easy loading and unloading. 

Causes of failure can include cracked/warped rollers from years of continual movement, accumulation of debris preventing free motion, or detachment of roller heads compromising installation.

Symptoms include:

• Difficulty fully extending or retracting racks  
• Off-tracking of shelving from left to right rails
• Scratches or damage to dishware from improper rack functioning 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Sump Overmold and Gasket Service Kit is an OEM part for GE dishwashers. Containing both the sump overmold and new gaskets, this kit replaces critical components in the lower dishwasher tub assembly.  

Causes of a bad sump or gaskets can include deterioration of rubber materials over multiple years of use and high heat. Mineral buildup during the wash cycle may also damage sealing surfaces.

Symptoms of a bad Sump Overmold and Gasket Service Kit include:

• Leaks or water entry in the bottom of the dishwasher 
• Excess moisture inside cabinet panels
• Inefficient or incomplete drying performance 

This genuine GE part is compatible with select Hotpoint, RCA and some Kenmore models as well.