Gsd4060dss Parts

This left-side door arm hinge secures and guides the appliance door, restoring proper alignment and smooth opening/closing. It replaces a bent or broken hinge to reduce sagging and uneven door movement. What it does:

• Supports the door on the left side and helps control its travel and position
• Restores proper door alignment when a hinge is bent, worn, or broken
• Helps eliminate door sagging, scraping, or uneven closing
• Works with existing hinge pins and mounting points to stabilize the door

• One left-side arm hinge

• Installation requires basic hand tools; refer to your model's service manual for step-by-step instructions
• Disconnect power (and water for washers) before starting any repair
• Inspect adjacent hinge hardware and fasteners; replace if worn to ensure proper fit and function

This right-hand arm hinge secures and guides the appliance door or access panel for proper alignment and smooth operation. It replaces a worn or broken hinge to restore correct door movement and positioning. What it does:

• Attaches the door to the cabinet and provides a pivot point for opening and closing
• Keeps the door aligned to prevent sagging, gaps, or rubbing
• Restores smooth, consistent door motion when the original hinge is bent, worn, or broken
• Helps reduce stress on the door and adjacent components caused by misalignment

• Install with power disconnected and appliance stable to avoid injury
• Tighten mounting fasteners securely but avoid over-torquing to prevent damage
• If replacing both sides or multiple components, inspect companion hinge and fasteners for wear

A stainless-steel #6-20 screw (1/2" length) used to fasten appliance panels and components securely. Durable corrosion-resistant finish helps maintain a tight fit and long-lasting hold in wet or humid areas. What it does:

• Fastens trim, brackets, panels, and internal components where a #6-20 x 1/2" screw is specified
• Provides a corrosion-resistant connection for areas exposed to moisture
• Restores loose or missing fasteners that cause rattling or misalignment
• Matches OEM thread and length for proper fit and function

• One stainless steel #6-20 x 1/2" screw

• Turn power off and unplug appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; stop when the component is snug and aligned
• Replace any additional damaged fasteners with matching OEM screws

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

A replacement clamp that secures hoses or wiring to keep lines routed and stable, helping prevent rubbing, leaks and noise. Restores a reliable hold for tubing and harnesses so the appliance runs quietly and safely. What it does:

• Holds hoses, tubing or wire harnesses in place to reduce movement and chafing.
• Helps prevent leaks and water line abrasion caused by loose fittings.
• Reduces rattling or vibration from unsecured lines or cables.
• Keeps routing organized so adjacent components aren't stressed or worn.

• Disconnect power before servicing the appliance; shut off water supply when working on water or drain lines.
• Remove the old clamp and position the replacement so it fully engages the hose or harness, avoiding twists.
• Use appropriate hand tools (pliers or screwdriver) and secure the clamp evenly; avoid overtightening.
• Inspect surrounding hoses and wiring for damage while installing; replace any components that show wear.

This switch interlock assembly secures the appliance door and completes the electrical circuit so the unit can start and run safely. Replacing a worn interlock restores reliable door sensing and helps ensure normal cycle operation. What it does:

• Detects and holds the door/lid closed so the appliance will start
• Completes the electrical pathway for motor and control circuits
• Prevents operation when the door is open or not fully latched
• Can stop mid-cycle or prevent starting when the interlock fails

• One switch interlock assembly

• Disconnect power (unplug or switch off the breaker) before replacing the part
• Handle mounting screws and wiring harness carefully; match connector orientation when reinstalling
• Verify door alignment and latch function before restoring power

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

This support calrod assembly secures and positions the oven/range heating element so it heats evenly and stays stable during operation. Replaces a worn or damaged support to restore proper element alignment and reduce rubbing or sparking. What it does:

• Holds the tubular heating element in the correct orientation inside the oven or range
• Prevents the element from sagging, contacting interior surfaces, or vibrating during use
• Helps maintain consistent heating performance and reduces risk of element wear
• Common symptom: element rubbing, touching oven walls, or uneven heat distribution

• One support calrod assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Handle heating elements and support parts carefully to avoid bending or damaging the element
• Follow OEM service instructions for removal and reassembly; verify correct element alignment before restoring power

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions

This inlet cover protects the washer's water valve and inlet area from debris and helps keep hoses and fittings secure for reliable water flow. It's a small replacement part that restores proper sealing and alignment at the inlet assembly. What it does:

• Covers and protects the water valve/inlet area from dirt and impact
• Helps maintain a secure fit for inlet hoses and fittings
• Can reduce or stop water weeping caused by a cracked or damaged inlet cover
• Restores correct alignment of inlet components after damage or wear

• Always disconnect power and shut off the water supply before beginning service
• Remove any retaining clips or screws and note their positions for reassembly
• Handle plastic parts gently to avoid cracking; replace any damaged fasteners