Gu980 Parts

This small plastic clip prevents your dishwasher's upper dish rack from sliding too far forward when pulled out. It stops the rack at the proper position to prevent it from falling out completely. Replace this clip if your upper rack slides out too far or falls off its tracks when loaded with dishes.

Secures the cup shelf to your dishwasher's upper rack. Replace this clip if it's broken, cracked, or missing to keep your cup holder stable and secure.

Protective rubber bumper for dishwasher dishrack. Installs on the outer front edge of the lower rack. Replace if cracked, broken, or missing.

Size: 8-32 x 1/4 inch.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Wire harness elbow connector for dishwashers. Replaces damaged, cracked, or broken electrical connectors that route power between components.

This door catch and strike work together to keep the door securely closed and engage the safety interlock switch. Replacing worn pieces restores a firm latch and reliable operation when the door is properly shut.

• Aligns and engages the latch so the door stays closed during operation
• Activates the door switch so cycles can start
• Helps prevent the door from popping open mid-cycle
• Common symptoms: door won't latch without force, unit won't start, visible wear or a bent strike

• Disconnect power to the appliance before servicing
• Open the door and remove mounting fasteners to swap the catch and strike
• Adjust strike alignment/depth so the latch engages fully and the door sits flush
• Restore power and test for smooth closing and proper cycle start

Replacement access panel covers the service opening on your dishwasher. Restores a finished look when the original panel is cracked, dented, or missing.

This channel retainer secures the appliance's front/side panel to the cabinet so panels stay aligned and stable during use. It replaces a worn or broken retainer to reduce panel movement and rattling. What it does:

• Holds the panel channel in place to keep exterior panels aligned
• Prevents panel looseness, shifting, and vibration noise during operation
• Restores proper fit where a cracked or broken retainer allowed gaps
• Works as a direct-fit replacement for the OEM channel retainer

• One channel retainer as shown

• Inspect surrounding clips and screws; replace any damaged fasteners for best fit
• Use basic hand tools; avoid over-tightening fasteners which can crack plastic retainers
• Disconnect power (or unplug) the appliance before accessing panels

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

Replacement mounting screw for securing panels, brackets, and components to your appliance chassis. Needed when original screws are stripped or missing.

Plastic cap that seals the drain line connection on your dishwasher. Replace if cracked, broken, or missing to prevent leaks and maintain proper drainage.