Ngm8056uc Parts

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

This replacement door gasket seals the dishwasher door to keep water inside the tub and help maintain wash performance. It restores a tight door seal to reduce leaks and prevent water from pooling around the appliance. What it does:

• Creates a watertight seal between the door and tub to stop leaks during cycles
• Helps prevent water from dripping onto floors and surrounding cabinetry
• Reduces steam and moisture escape that can cause odors or damage
• Restores proper door closure where worn or flattened seals allow seepage

• Disconnect power and water supply before attempting any service.
• Inspect surrounding door edges for damage and clean mounting surfaces before installing the new gasket.
• Press the gasket firmly into the door channel; some models require partial door disassembly.
• After installation, run a short cycle and check for leaks before returning the dishwasher to regular use.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where the original screw is missing, stripped, or damaged to help keep parts aligned and stable. What it does:

• Fastens panels, brackets, or components to maintain proper alignment and operation
• Replaces a lost, stripped, or damaged screw to prevent rattling or loose parts
• Provides the same basic fastening function as the original hardware
• Suitable where the appliance requires a small machine/tapping screw of the correct size and thread

• One replacement screw

• Use the correct screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure proper engagement before tightening
• Tighten snugly but avoid over-torquing which can strip threads or damage parts
• Disconnect power to the appliance before working on or removing panels where appropriate;

This replacement cable is a direct-replacement wiring harness used to restore electrical connections for the appliance control and components. It provides the needed wiring continuity so controls and sensors can communicate reliably. What it does:

• Reestablishes a secure electrical connection between components and the main control
• Restores signal/power routing when a frayed or damaged wire causes intermittent operation
• Can resolve symptoms such as failure to power on, intermittent cycles, or related error codes tied to wiring faults
• Prevents shorting or poor contact that can lead to inconsistent appliance behavior

• Recommended for technicians or experienced DIYers; disconnect power before replacing
• Verify matching connector shapes and wire colors before installation
• Route the cable away from heat and moving parts to avoid future damage

This hob top is the replaceable glass cooktop surface that restores a flat, stable cooking area and protects internal components from spills and heat. It helps keep burners aligned and the cooktop looking finished. What it does:

• Provides the main glass surface for the cooktop, forming the top of the cooking area
• Protects internal burner assemblies, wiring, and controls from spills and debris
• Restores a smooth, even surface for cookware to sit on after damage or cracking
• Helps prevent heat and moisture from reaching internal components when properly installed

• For safety, disconnect power at the breaker before starting repair
• Handle glass with care; use proper support and protective gloves to avoid breakage and injury
• Follow manufacturer service instructions for removal and reinstallation to ensure proper alignment and sealing

This holder is a small retainer used to secure internal components in place, restoring proper alignment and stopping loose parts from shifting during use. It helps reduce rattling and prevents components from disengaging. What it does:

• Secures and stabilizes a specific internal component or assembly
• Stops rattling and vibration caused by a loose or missing retainer
• Prevents a part from slipping out of position during operation
• Helps restore normal fit and alignment of the affected assembly

• Disconnect power before accessing internal parts
• This part typically snaps or screws into place; inspect surrounding clips and fasteners
• Handle small plastic parts carefully to avoid cracking; replace any damaged adjoining clips

This replacement holder is a small mounting bracket that secures components inside the appliance, restoring proper alignment and stable operation. It replaces worn or broken holders to help prevent rattling and misalignment. What it does:

• Secures internal components or assemblies to the appliance frame
• Restores proper alignment to reduce movement, noise, and wear
• Helps maintain correct positioning for connected parts to function reliably
• Commonly replaced when the original holder is cracked, warped, or missing

• One replacement holder

• High-level replacement: usually fastener-mounted or snapped into place; inspect surrounding clips and fasteners
• Power safety: disconnect power (and water for dishwashers/washers) before accessing internal components
• Use correct fasteners and avoid over-tightening to prevent cracking the new holder