Pdb17 Parts

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

Replace your dishwasher shaft seal to stop leaks around rotating components. Restores watertight protection for bearings and internal parts. Verify fit.

Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.

Fix poor spray coverage with this dishwasher jump-up nozzle. Replaces worn or clogged nozzles that cause uneven cleaning. Simple DIY repair.

Fix loose or rattling dishwasher trim panels with this dispenser retainer clip. Secures interior panels and exterior trim for proper fit. Easy repair.

Fixes dishes not drying properly. This dishwasher heating element restores heat for effective drying cycles. Straightforward replacement part.

A replacement appliance door handle that restores a secure grip and proper operation to a worn or broken handle. Designed to match the original mounting style for a clean, factory-fit appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door smoothly
• Replaces cracked, loose, or broken handles that affect normal door use
• Restores correct alignment and leverage to reduce strain on door components
• Helps prevent accidental drops or slippage when grabbing the door

• One replacement handle

• Remove power and empty the door area before starting any repair
• Typical install requires removing trim or screws; use manufacturer-recommended fasteners
• Retain original mounting hardware unless the new handle explicitly includes replacements

8-32 x 3/8" machine screw secures dishwasher control panels, brackets, and interior assemblies. Replace missing, stripped, or lost screws during repairs.

Mounts the lower spray arm assembly to the pump housing in your dishwasher. Replace if cracked, broken, or worn to restore proper spray arm installation.

Secures the power cord where it enters the cabinet, protecting the jacket and preventing pull on internal connections. Replace if cracked, broken, or missing.

This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.

• Seals the dispenser passage to keep water from leaking into or out of the dispenser cavity
• Helps ensure proper detergent or rinse-aid dispensing
• Can reduce moisture-related corrosion or staining in the dispenser area

• Disconnect power and turn off water before servicing
• Remove inner door panel to access the dispenser assembly
• Note grommet orientation; seat fully to ensure a watertight seal
• Inspect surrounding surfaces for debris or damage before reassembly

This switch holder secures a small appliance switch or actuator in the correct position so the control can detect and respond reliably. Replacing a cracked or broken holder restores consistent switch alignment and helps prevent intermittent operation. What it does:

• Holds the switch or actuator steady in the correct position for reliable electrical contact and activation
• Keeps the switch aligned so buttons, door/lid actions, or control functions register properly
• Common symptom: appliance function won't engage or is intermittent when the switch is loose or the holder is damaged
• Prevents further wear on the switch by keeping it from shifting or rubbing against surrounding parts

• Disconnect power (unplug or shut off breaker) before servicing the appliance
• Remove the control panel or access panel to reach the holder; keep small clips and screws organized
• Inspect the switch and actuator for damage while replacing the holder; replace any damaged mating parts

Replacement handle mounting screw for refrigerators. Secures the door handle to the appliance. Order if your original screw is stripped, missing, or lost.

Replace your dishwasher's worn or missing washer. Installs on spray arm pipe or door components. Needed when old washer is cracked or damaged.