Flame Sensor Parts

Fridge not cooling but freezer works? This defrost thermostat monitors evaporator temperature to prevent frost buildup. Tests closed when cold with multimeter.

Oven won't heat or suddenly stops working? This thermal fuse cuts power when temperatures exceed safe limits. Moderate DIY repair in 30-45 minutes.

Microwave won't start or stops mid-cycle? A blown fuse is often the culprit. This 5 amp fuse protects your microwave's electrical system. Quick DIY fix.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Freezer not cooling or frosting over? This defrost thermostat monitors temperature and controls the defrost cycle to prevent ice buildup and restore airflow.

This evaporator wire harness delivers power and control signals to the evaporator fan and defrost components. Replace a damaged harness to restore stable cooling and dependable automatic defrost performance. What it does:

• Provides plug-in electrical connections for evaporator-compartment components
• Carries power and control signals for cooling and defrost cycles
• Enables proper airflow across the evaporator and effective frost removal
• Common clues of a failing harness: heavy frost on the back wall, evaporator fan not running, intermittent cooling, or burned/brittle wires or connectors

• 1 evaporator wire harness assembly

• Disconnect power to the refrigerator before servicing
• Access the harness behind the freezer/evaporator cover; remove drawers/shelves and the rear panel
• If iced over, allow ice to melt—do not use sharp tools on coils or wiring
• Route and secure the new harness exactly like the original; fully seat each connector

This safety device monitors dryer temperature and shuts off heating when preset limits are exceeded, located near the heating element or exhaust. Replace it when clothes aren't drying properly, the dryer overheats, or heating stops working entirely.

Oven overheating or won't heat properly? This safety thermostat monitors backguard temperature to prevent overheating. Simple DIY fix restores safe operation.

The Moisture Sensor is an OEM component specifically designed for Whirlpool washing machines. The sensor monitors moisture levels to determine when the appropriate moisture point has been reached, signaling the appliance to advance to the next step in the cycle.

Symptoms of a bad moisture sensor include: 

• Inability to advance through entire wash cycle  
• Immediate ending of cycle after short period of time
• Sensor may show moisture levels incorrectly
• LED lights indicating error codes related to moisture detection

Causes of a bad moisture sensor can be due to cracks, corrosion, or damage to its sensitive electronic components from impact or overuse. Regular cleaning and maintenance helps extend the life of the moisture sensor. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This thermostat monitors the evaporator coil temperature and signals the defrost heater to turn on or off during the defrost cycle. It prevents excessive frost buildup on the evaporator, which is essential for proper cooling in the refrigerator. Replace this part if you notice heavy frost accumulation on the back wall of the freezer, the refrigerator is not cooling properly, or the defrost cycle is not activating.

Fix a refrigerator that won't cool or frosts excessively with this defrost thermostat. Senses temperature to control the defrost cycle properly.

 The Thermostat is an OEM part for Whirlpool microwaves. It is a temperature-sensitive component that monitors heat levels inside the oven cavity during operation.

Causes may include damage from exposure to moisture or debris over time that disrupts accurate readings.

Symptoms of a faulty thermostat include:

• Incomplete or inconsistent heating with uneven hot/cold spots
• Food not reaching expected doneness after preset times
• Overheating errors or cycle interruptions

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a thermal cut-out safety device that shuts off the microwave when internal temperatures exceed safe operating limits. It functions as a protective thermostat to prevent overheating and potential damage to the appliance. Replace this part if the microwave shuts off unexpectedly during use, fails to power on, or if the unit is overheating.