Whirlpool Dryer Repair Kit 4392065 Installation Guide

Is your Whirlpool dryer making strange noises or refusing to start? You might be facing common issues that often stem from worn-out parts. Fortunately, our comprehensive guide and step-by-step how-to video, found just below, are here to walk you through replacing these parts with the Whirlpool dryer repair kit—saving you time, money, and frustration!

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

The Whirlpool dryer repair kit includes several parts that are commonly replaced to keep your dryer running smoothly. Over time, these parts can wear out or break, leading to various issues like odd noises during operation, the drum refusing to spin, or the dryer not starting at all. Replacing all of the parts in the kit at the same time saves money and prevents future repairs. 

The installation of the Whirlpool dryer repair kit is a relatively straightforward process that can be done with basic tools. On average, the repair should take approximately 30 to 60 minutes, depending on your familiarity with repairs. By following the steps in this guide, you can save time and money by completing the repair yourself. So, grab your tools, roll up your sleeves, and let’s get your Whirlpool dryer up and running like new again!

Watch here: How To: Whirlpool/KitchenAid/Maytag Repair Kit 4392065

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

What’s included

• Drum belt (341241)
• Drum support roller (WPW10314173)
• One idler pulley (WP691366)
• Push clip (WP90296)
• Drum support sheel retainer (WPW10512946)
• Instruction sheet

What you’ll need

• Phillips screwdriver
• Flat blade screwdriver
• 5/16” nut driver
• Putty knife

Safety precautions

• Always power off and unplug your appliance or switch off the circuit breaker before attempting any maintenance or replacement work. This keeps you safe by preventing any risk of injury from electric shock.
• Turn off the water supply at the outlet before beginning repairs to any appliance parts that hold water. Have towels ready for any residual water in the system when removing parts. 
• Wear insulated work gloves to protect your hands from sharp metal parts, pinching hazards and debris.
• Don’t test wiring with a multimeter for live voltage if you’re unfamiliar with how to prevent short circuiting when testing. 
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.
• Take your time and don’t rush while working to prevent accidents and personal injuries.
• Work in a well-lit area so you can clearly see and access the interior parts.
• Clear your workspace of clutter and other obstacles. Keep children and pets away from the work area.
• Check your user manual to see if there are specific installation or safety instructions for your part or appliance. 
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause injury.
• Wear safety glasses when working with chemicals, dust or cleaning large debris to prevent injury. 
• If the appliance has recently been used, give it plenty of time for any hot parts to cool down before working on it. 

Replacement steps

Removal

1. Pull out the lint filter from the top panel.
2. Use a Phillips screwdriver to loosen and remove the two screws that secure the lint trap assembly to the top panel.
3. Take a putty knife and insert it between the top panel and the front panel, near the top locks. Press in with the putty knife to release the locks on both sides.
4. Release the other top lock using the same method.
5. Carefully tilt back the top panel assembly and prop it up to keep it in place.
6. Locate the wiring harness that connects to the door switch. Use a small flat blade screwdriver to lift the tabs and disconnect the wiring harness.
7. Look for the two screws that hold the front panel assembly in place. Use a 5/16 inch nut driver to loosen and remove these screws.
8. Lift up slightly on the front edge of the dryer drum and then tilt the front panel forward.
9. Lift up on the front panel to release it from the two mounting tabs and remove the front panel assembly.
10. To remove the dryer drum assembly, you need to disconnect the drive belt assembly. Pull back on the idler pulley to relieve tension on the belt and remove the belt from the drive pulley.
11. With the drive belt disconnected, lift up and remove the drum from the dryer cabinet.

Replacement

1. To replace the drum rollers, use a small flat blade screwdriver to pry up and remove the triangle-shaped retainer from the drum roller shaft.
2. Remove the old drum roller and replace it with a new one.
3. Remove the triangle-shaped clip that secures the rear of the drum roller and install a new rear clip. Then, install the new front clip.
4. To remove the second drum roller, remove the heat shield first. Use a 5/16 inch nut driver to loosen and remove the two screws that retain the heat shield, then remove the shield.
5. Use a small flat blade screwdriver to pry off the metal retaining clip. Then, use a 5/16 inch nut driver to remove the screw that retains the drum roller support bracket.
6. Remove the old drum roller and replace it with a new one.
7. Remove the triangle-shaped clip that secures the rear of the drum roller and install a new rear clip. Then, install the new front clip.
8. Reposition the drum roller support bracket and press the new metal retaining clip onto the shaft. Thread and tighten the retaining screw. Reinstall the heat shield and tighten the two retaining screws.
9. Remove the old idler pulley assembly by sliding it out of the cabinet and install the new idler pulley in its place.
10. Tilt the drum forward slightly and place the new belt around it. Make sure the ribbed edge of the belt faces down onto the barrel.
11. Lift the drum and position the end of the belt between the idler pulley and the pulley bracket. Push back on the idler pulley assembly to create tension, and then position the belt on the motor pulley. Release the pressure on the idler assembly to tension the belt and remove any slack.
12. Position the front panel so that the bottom of it rests on the two mounting tabs. Lift up on the front edge of the dryer drum and tilt the front panel into place.
13. Thread in and tighten the two screws that hold the front panel in place.
14. Reconnect the wiring harness for the door switch.
15. Lower down the top panel, aligning the tabs, and push it into place.
16. Thread in and tighten the two screws that secure the lint trap assembly to the top panel.
17. Reinstall the lint filter. Reconnect the power cord. Your dryer is now ready to run a test and check for any problems.

Additional information

Thanks for reading! We hope this guide helped you replace the repair kit on your Whirlpool dryer. 

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter and Instagram to see our latest repair guides!