Black Max Engine Parts

Installing a brand-new air filter keeps the engine in top running condition. When the machine is in operation, the vacuumed air goes through the air filter. Any dirt or dust is left in the filter media. Over time, the filter will become dirty and can no longer provide the same filtering efficiency as before. If left ignored, the tiny particles could clog the engine and the carburetor. You may experience misfires and no engine start-up. An air filter replacement is cheap and easy to do. Simply remove the air cleaner cover and take out the dirty filter. Insert the new filter into the housing. This replacement will take less than 5 minutes. A screwdriver will be needed. The MTD 951-10298 Air Cleaner Kit is a genuine air filter from MTD. Each kit comes with one paper filter and one foam filter. The foam filter can be cleaned with water and detergent. The paper filter, however, needs replacement at least once a year. This air filter kit is compatible with Cub Cadet, PowerMore, and Troy-Bilt. It can also work with other garden equipment like wheel string trimmers, chipper-shredder vacuums, and log splitters.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This is a genuine OEM replacement part for select Honda and MTD push lawnmower engines. This lawnmower fuel filter is essential for optimal engine performance. The part consists of a small red plastic rod and serves as a filter to ensure clean fuel is entering the engine. It will require replacement over time after clogging.The filter is responsible for screening dirt and other particles such as dust and debris from the fuel in order to prevent engine damage. Without this part, small particles can get trapped in the carburetor, which can potentially wreak havoc on the engine. Going for long periods of time without replacing the fuel filter can jeopardize the rest of the machinery. In addition, fuel filters will slowly clog up over time with accumulated debris, starving the engine of fuel. Signs to watch for that might indicate the fuel filter needs to be replaced include rough idling and an engine that will not remain running.Using a damaged or old fuel filter. The filter replacement is sold individually only.

This governor arm shaft can be used as a replacement part for hedge trimmers, string trimmers, lawnmowers, or chipper shredders. The governor arm shaft for one of these small engine appliances is a connecting part within the governor system; it is fastened to the governor cross shaft and is attached to the throttle linkage and the governor spring. Governor arm shafts can be subject to damage in the form of erosion, piercing, puncturing, or general wear and tear. Damage to a governor arm shaft can affect all of the surrounding components. As such, if a governor arm shaft suffers damage such that it cannot fasten components together, it must be removed and replaced immediately before the small engine appliance can be used again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This governor arm shaft is a genuine OEM part sourced from MTD. It is sold individually. It is compatible with the following brands: MTD, Cub Cadet, Craftsman, and Yard Machines.

This is a piston that is designed for use with several types of lawn and garden equipment. The main purpose of the piston is to seal off the pressurized combustion chamber from the crankcase. It takes the combustion power and transfers it to all of the working parts of the equipment. If the piston is going bad or has been damaged, the tool may have poor performance, the exhaust may create white smoke, or the equipment may burn oil excessively.A compression test can determine whether the pisons are malfunctioning. This involves taking a spark plug out of the engine and then starting the tool with a compression gauge attached to the cylinder where the spark plug used to be. If there is a problem with the compression, the piston will need to be replaced.This piston is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The piston is designed to be compatible with lawnmowers, tillers, string trimmers, edgers, log splitters, and wood chippers manufactured by Cub Cadet, Craftsman, and MTD.

This is a piston pin that is used in many types of small engine lawn and garden equipment. The piston pin is a component that connects the connecting rod to the piston. It acts as a bearer that allows the connecting rod to pivot whenever the piston is moving. The pin is a hollow rod made of durable materials but constant wear and tear can damage the part or cause it to break.If the piston pin is broken or damaged, it will need to be replaced. A pair of pliers and an Allen wrench may be needed to complete the replacement. The process involves removing the access covers and the housing from the piston crank. The old piston ring can be removed from the connecting rod so the new component can be installed. After installation, reassemble the equipment.This piston pin is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The pin is designed to be compatible with wood chippers, log splitters, edgers, string trimmers, tillers, and lawnmowers manufactured by MTD, Craftsman, Yard Machines, and Cub Cadet.