Parts for Ge GDL3023RAL: Control Panel Parts

Cover plate for dryer installation. Replaces cracked, broken, or missing caps. Provides a finished appearance and protects internal components.

This is a small 8-32 threaded nut used as a fastener in various mounting locations within the refrigerator. It secures internal components and brackets in place to maintain structural integrity. Replace this nut if it has become stripped, corroded, or lost during a previous repair, causing a loose or rattling component.

12-pack mounting screws for various appliances. Replaces missing, stripped, or damaged screws used to secure panels, brackets, and components.

7" diameter

Ground strap assembly connects drum shaft to dryer frame for electrical safety. Replace if damaged, corroded, or causing startup squealing noise.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Size: 8-32 t. Includes 12 screws.

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

This adjustable gray foot supports and levels your dryer, allowing you to compensate for uneven floors. It screws into the dryer's base and can be raised or lowered to ensure the appliance sits level and stable. Replace this part if your dryer rocks, vibrates excessively, or appears tilted.

Fixes dryer not heating or overheating issues. This safety thermostat monitors temperature and cuts power when too hot. Basic DIY repair, 30 minutes.

Black. 8-18 AB HXW 3/8

Seals the gap between drum and bulkhead in your dryer. Replace when worn to eliminate scraping noises, prevent fabric snags, and maintain airflow.

Dryer not heating? This heating element assembly restores heat when coils burn out. Straightforward DIY repair with basic tools in 1-2 hours.

Bearing only, to get complete assembly order WE25M40

Fix a dryer that won't start or has a broken start knob. This rotary start switch is located in the control panel. Easy 5-10 minute DIY repair.

Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.

This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.

• Drives the drum via the belt and turns the blower wheel for airflow
• Helps resolve: dryer hums but won't start, drum won't turn, or stops mid-cycle
• Can reduce loud buzzing/grinding noises from the motor area
• Restores consistent operation when the motor overheats and trips its protector

• Disconnect power; turn off gas supply to gas dryers before servicing
• Remove panels to access the drive system; release belt tension and remove the drum as needed
• The blower wheel threads onto the motor shaft—support it carefully; many GE dryers use a reverse (left-hand) thread
• Transfer wiring and any reusable hardware to the new motor; test before reassembly

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Connects motor to drum for rotation. Replace if dryer won't start, makes noise, or drum doesn't turn. Confirm fit with your model number before ordering.

The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping. 

Symptoms of a bad Idler Pulley include:

• Squeaking or screeching noises during dryer operation, often a sign of bearing wear or failure.
• The dryer drum not turning smoothly, or at all, indicating that the belt may be slipping or has come off entirely due to a failed pulley.
• Excessive heat or a burning smell, which can occur if the pulley is seizing up and causing friction.
• Visible wear or damage to the pulley itself.

Causes of a bad idler pulley can include worn bearings, accumulation of lint and debris that impedes rotation, or material fatigue after prolonged use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.