Kitchenaid Range Hood Parts

The Grease Filter is an OEM part for Whirlpool range hoods. This part traps grease particles from the air as it circulates through the range hood, preventing grease buildup on the blower and other internal components, thus maintaining the efficiency and longevity of the range hood.

Causes of a bad grease filter can include clogging from excessive grease accumulation, physical damage from improper cleaning or handling, and general wear and tear over time.

Symptoms of a bad grease filter include:

• Reduced air flow from the range hood
• Visible grease buildup on or around the filter
• Unusual odors persisting in the kitchen
• Filter appearing worn or damaged

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Control Knob is an OEM component specifically designed for Whirlpool and KitchenAid ranges. Located on the range control panel, this knob securely attaches to the temperature dial and allows for easy adjustment of burner temperatures. A dependable control knob facilitates simple, intuitive stovetop operation.

Causes of a faulty knob can include wear from frequent use, damage or cracks to the knob base or connector, or premature degradation of plastic components. 

Symptoms of a bad control knob include:

• Loose, wobbly, or detached knob that won’t stay securely in place
• Difficulty adjusting burner heat levels precisely  
• Potential knob breakage or non-functional temperature dial 
• Inability to maintain desired cooking temperatures

This OEM part is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This slide-style electrical switch selects or turns a function on and off inside the appliance. Replacing a worn switch restores reliable control when settings won't engage, respond intermittently, or the slider feels loose or broken. What it does

• Provides sliding on/off or multi-position selection for a specific feature
• Routes power to the associated component when a position is selected
• Helps restore proper response when a control becomes intermittent or unresponsive
• Common signs: slider sticks, feels loose, breaks, or shows heat discoloration on terminals

• 1 slide switch

• Disconnect power to the appliance before service
• Access the control panel; note wire locations and take a clear photo
• Move wires to the new switch one at a time; fully seat each connector
• Reassemble, restore power, and test each switch position

This replacement grease filter captures airborne grease and cooking residue in your appliance's venting system, helping protect the blower and ductwork while maintaining effective ventilation and airflow.

• Traps grease and food particles carried by the exhaust airstream
• Helps sustain proper airflow and reduce smoke and lingering odors
• Replace if mesh is torn, warped, missing, or remains clogged after cleaning
• Common symptoms include persistent smoke/odors, visible grease buildup, or a loose/rattling filter

• Disconnect power before servicing and allow the appliance to cool completely
• Open the filter access, release the retaining latch or screws, and remove the old filter
• Slide the new filter into place, matching the original orientation/tabs
• Ensure the filter is fully seated and secured; do not operate the unit without a filter

A direct-replacement rocker switch for control panels that restores a positive on/off or function selection when the original switch has worn or failed. Fits common Whirlpool control-panel applications to help regain reliable button function. What it does

• Opens and closes the electrical circuit for a specific control function on the appliance control panel.
• Replaces a worn, cracked, or non-responsive rocker that fails to click or hold a selection.
• Can resolve intermittent operation, no power to a single function, or tactile button failure.
• Designed to match OEM terminal layout for a direct electrical swap when the correct part is used.

• One rocker switch.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Remove the control panel or access panel to reach the switch; note wire positions or take a photo before disconnecting.
• Pull off quick-connect terminals with pliers or a terminal tool and transfer wires to the replacement in the same order.
• After installation, restore power and test the function before fully reassembling the appliance.

This filter traps cooking grease and airborne particles as air moves through your appliance's ventilation system. It helps protect the blower and internal surfaces and supports proper airflow for effective venting during everyday cooking.

• Captures grease and debris from cooking vapors to reduce buildup on internal components
• Helps maintain ventilation airflow and fan performance
• Replace if the mesh is torn, warped, heavily clogged, or no longer stays seated
• Common symptoms include reduced airflow, lingering smoke or odors, and visible grease accumulation

• Disconnect power and allow surfaces to cool before servicing
• Access the filter from the underside of the hood or over-the-range unit
• Release retaining tabs or screws, remove the old filter, and slide the new filter into place
• Ensure the filter is fully seated and secured before restoring power

This rocker switch restores dependable on/off control for a selected function on your appliance. Replace a worn or intermittent switch to fix features that won't turn on or off and bring normal operation back. What it does:

• Controls power to a single function when pressed
• Common symptoms: feature won't turn on/off or only works intermittently
• Switch feels loose, sticks, or requires wiggling to engage
• Resolve issues caused by worn internal contacts or heat discoloration

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Note wire positions or take a photo; move wires to the new switch one at a time
• Seat the switch securely in the panel or bracket to avoid pinched wires
• Restore power and test operation

This is a replacement refrigerator water filter cartridge that helps restore clearer, better-tasting water and ice. Use when your dispenser or ice maker produces cloudy water, unpleasant taste or odors, or reduced water quality. What it does:

• Traps common particles and sediment that cause cloudy water
• Reduces chlorine taste and odor to improve water and ice flavor
• Helps maintain normal dispenser and icemaker performance related to water quality
• Provides a direct-replacement fit when the OEM filter is removed and replaced

• Turn off the water supply and dispense water to relieve pressure before removing the old filter.
• Remove the old filter per your refrigerator's OEM instructions and install the new cartridge until it seats securely.
• Run several gallons of water through the dispenser after installing to flush the system and clear air.
• Follow the refrigerator OEM for recommended replacement interval and any filter reset procedures.

This replacement refrigerator water filter helps maintain clear, better-tasting drinking water and ice by trapping common impurities. Designed to restore filtered water performance when the original cartridge is due for service. What it does:

• Reduces taste and odor issues from chlorine and other common contaminants commonly found in public water supplies
• Helps deliver cleaner ice and drinking water from the refrigerator dispenser
• Restores proper flow and filtration when the installed filter is clogged or aged
• Compatible with refrigerators that use this specific OEM filter cartridge design

• One replacement refrigerator water filter cartridge

• Turn off the water supply and before starting
• Replace filter according to manufacturer instructions; flush several gallons of water after installation to clear air and carbon fines
• Dispose of the old cartridge properly and check for leaks after reconnecting the water

A duct kit designed to route a dryer's exhaust safely to the household vent system, restoring proper airflow and helping the dryer vent effectively when the original ducting is damaged or missing. What it does:

• Channels hot, lint-laden exhaust from the dryer to the exterior vent to reduce indoor heat and moisture.
• Replaces crushed, torn or disconnected ducting that can cause poor drying performance.
• Use when you notice longer dry times, excess heat or lint buildup near the dryer, or backdrafting from the vent.
• Helps maintain proper vent airflow when installed and secured per manufacturer and local code requirements.

• Disconnect electrical power (and gas supply for gas dryers) before installing or servicing venting components.
• Follow the appliance manufacturer's installation instructions and local building/venting codes for diameter, length and material.
• Avoid crushing, kinking or sharp bends in the duct; secure joints with approved clamps or foil tape and check for leaks.

This replacement refrigerator water filter helps improve water and ice taste by trapping common impurities. It restores cleaner-tasting water for drinking and cooking when your existing filter is old or clogged. What it does:

• Filters water to help reduce common contaminants that affect taste and clarity
• Helps improve the taste and odor of dispensed water and ice
• Addresses symptoms like unusual water taste, cloudy ice, or reduced water flow from the dispenser
• Restores proper filtering performance when the old filter is past its service life

• Turn off water supply to the refrigerator before removing the old filter.
• Follow your refrigerator's filter removal/installation steps; typically push/rotate or pull to remove and insert until secure.
• Flush several quarts of water through the dispenser after installation to clear air and initial carbon fines.
• Dispose of the used filter according to local regulations.

The Capacitor is an OEM part for Whirlpool range hoods. This capacitor functions to optimize blower motor performance. It works in tandem with the motor to efficiently expel cooking vapors and gases from the kitchen.

Causes relate to standard wear over extended use of the vent hood. Electrical issues can cause premature capacitor failure.  

Symptoms of a bad capacitor include:

• Reduced air circulation and weaker ventilation
• Abnormal humming or grinding noises from the motor
• Failure of the blower to turn on as desired

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This socket is an electrical wire terminal that provides a secure connection between wiring and a compatible appliance component, helping restore reliable power transfer and prevent loose or intermittent connections. What it does:

• Accepts and holds a mating terminal to complete an electrical circuit
• Restores a secure wire-to-component connection when the original socket is damaged or worn
• Helps stop intermittent power, sparking, or heating at a loose connection
• Used where a durable, removable terminal interface is required

• One socket terminal (single piece)

• Turn off and disconnect power to the appliance before servicing
• Inspect mating terminals and wiring; replace any damaged wires or connectors
• Push the mating terminal fully into the socket until it locks; ensure proper orientation

This upper vent cover replaces the visible duct cover on a range hood to restore proper appearance and help channel exhaust air. It provides a finished look and protects ductwork from grease and debris. What it does:

• Covers the vent duct above the hood for a clean, finished appearance
• Helps direct exhaust up into the duct while protecting internal components from dust and grease
• Use when the original chimney is dented, cracked, or cosmetically damaged
• Reduces visible gaps between the hood and ceiling when properly installed

• Designed to mount to the hood body or chimney assembly; follow OEM mounting points
• May require removal of the hood's grease filters or upper panel for access
• Ensure power is off to the appliance before starting work to avoid electrical hazards
• Replace damaged ducting or fasteners as needed for a secure fit

This rocker switch replaces a worn or failed control switch to restore reliable user control of the appliance. It fits the original switch location and provides a simple, replaceable interface for operating the circuit. What it does

• Acts as the user-facing rocker control to open and close the electrical circuit for the function it controls.
• Replaces intermittent or non-responsive rocker behavior so buttons toggle correctly.
• Common symptoms it addresses: switch doesn't actuate, feels loose, or the controlled function won't turn on/off.
• Works as a direct replacement for the original rocker control found behind the panel.

• One rocker switch

• Disconnect power (unplug appliance or shut off breaker) before starting any repair.
• Remove necessary access panels and use basic hand tools to replace the switch; handle wiring and terminals carefully.
• Verify correct switch operation before reassembling trim and panels.