Maytag Garbage Disposal Parts

This installation kit includes the manufacturer-specified components needed to complete a secure, correct install of the designated appliance or accessory. Use it to replace missing pieces and finish the job with proper fit, alignment, and stability.

• Provides the parts required by the manufacturer to complete installation
• Helps ensure secure mounting and correct positioning
• Useful for new installs, re-installs, or when original hardware is missing or damaged
• Common indications you need this kit: incomplete installation, loose fit, or missing hardware

• Disconnect power and shut off any water supply before starting
• Follow the installation instructions provided with the kit and your product
• Use appropriate tools; check level and clearances before final tightening; get help lifting heavy units

This mounting gasket creates a tight, cushioned seal where a component attaches to its housing or bracket. Replacing a worn seal helps stop leaks and rattles while restoring a secure, reliable connection at the mounting point.

• Forms a seal between two mounting surfaces to help prevent leaks or seepage
• Cushions and isolates vibration for quieter operation
• Helps maintain proper alignment of the mounted component
• Replace if the gasket is cracked, flattened, brittle, or no longer sealing

• Disconnect power and shut off water or gas, if applicable
• Note the gasket's orientation before removal
• Clean and dry both mating surfaces; remove all old gasket material and residue
• Seat the new gasket evenly; reassemble and tighten fasteners snugly without overcompressing; test for leaks/operation

This is a replacement Seal - stopp that restores a secure seal to the original component, helping prevent leaks and keep the appliance operating normally. Use it when the original seal is worn or damaged. What it does

• Forms a tight seal at the mating surface to help stop water or air leaks
• Restores proper fit where a worn seal causes seepage or dripping
• Helps reduce related symptoms like water pooling beneath the appliance or visible leakage
• Simple, single-piece part designed to match the OEM sealing point

• Disconnect power to the appliance before starting work; turn off water supply if applicable
• Inspect mating surfaces and clean away debris or old sealant before installing the new seal
• Fit the seal fully into its groove or mounting location; do not stretch or twist the part during installation

This metal tailpipe directs dryer exhaust from the appliance outlet to the vent system, restoring proper airflow and helping prevent exhaust leakage. It's a direct-fit replacement that reinstates safe venting. What it does

• Channels exhaust air from the dryer outlet to the vent duct to maintain proper airflow
• Helps prevent exhaust leakage behind the dryer that can cause odor or moisture issues
• Stops rattling or misalignment at the dryer outlet caused by a damaged or bent tailpipe
• Supports safe venting performance that can affect drying efficiency

• One tailpipe

• Disconnect power; for gas dryers, shut off the gas supply before starting
• Basic tools (screwdriver/socket) typically required; follow OEM installation instructions
• Ensure the tailpipe is seated and secured to the dryer outlet and vent duct with proper clamps or screws
• After installation, check for leaks, proper alignment, and test dryer operation

This stopper assembly seals the drain opening to allow tubs or sinks to fill and hold water. It replaces a damaged or worn stopper so you can restore proper fill-and-hold function and stop unwanted leaks. What it does

• Seals the drain to hold water for washing or soaking
• Opens and closes to allow controlled draining when needed
• Stops water from leaking around a worn or damaged stopper
• Restores normal fill-and-drain operation when the original stopper no longer seals

• One stopper assembly as shown

• Turn off water supply and remove standing water before starting
• Basic hand tools usually required; follow the appliance or sink manufacturer instructions
• Inspect surrounding drain and seals during replacement; replace damaged gaskets if present

This sink flange seal is a rubber gasket that creates a watertight seal between the sink and drain flange to help prevent leaks and water damage. Use it when the flange seal is cracked, flattened, or leaking. What it does:

• Seals the gap between the sink and drain flange to stop water from leaking under the sink.
• Helps prevent sink-edge water pooling and slow drainage caused by a failed seal.
• Reduces chance of odors from trapped water beneath the flange by restoring a tight seal.
• Restores proper fit when replacing a corroded or worn sink flange assembly.

• One sink flange seal (rubber)

• Turn off water supply and disconnect drain components before replacing the seal.
• Remove the drain flange assembly, clean mating surfaces, then seat the new seal evenly.
• Avoid stretching or cutting the seal; replace it if damaged or misshapen.