Mtd Pro Blade

A mulching blade has a unique curved or angled design that allows discharging, bagging, and mulching. If its edges are already dull, it can lead to longer mowing time and frayed and torn grass blades. Mulching blade installation is easy. First, unplug the spark plug wire. Then, position the lawnmower on its side. Get a woodblock, preferably 6 x 2 in size, and put it between the old blade and housing deck. Make sure that the wood will prevent the old blade from moving. Take a socket wrench and remove the blade’s nut and washer. Remove the old blade and put the new mulching blade in. Put the nut and washer back and tighten until it is secured. You can use the woodblock to prevent the replacement blade from moving when it is tightened. This mulching blade replacement s an original MTD product. This OEM mulching blade can be used for MTD, Craftsman, Cub Cadet, Murray, Yard-Man, and Bolens lawnmower models. This brand-new mulching blade is sold individually. The support blade and screw hex are sold separately.

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

This scraper blade is an authentic OEM replacement part for a snowblower. Snowblowers operate using an auger that scoops up the snow and blows it to a different location. However, an auger cannot gather all of the snow because it would have to scrape against the ground. Scraping that auger against the ground would damage its blades and make them unusable. Instead, this scraper blade drags against the ground and collects any remaining snow so that the auger blades can remain protected. Scraper blades can be damaged if the snowblower goes over rocky terrain. Although it is nearly impossible for a blade to snap completely off a blower, the blade will leave the snow behind, making the blower less effective if chipped or dented. To replace a scraper blade, simply use a socket wrench to unbolt the blade from the auger housing. Be sure not to lose the bolts as they will be needed for reassembly. This part is compatible with Craftsman, MTD, Cub Cadet, Ryobi, Huskee, Yard Man, and Yard Machines snowblowers and is sourced from the original manufacturer. This part is a high-quality replacement part. It does not ship with additional hardware.

This is a replacement shave plate for use with snowblowers. The plate attaches to the bottom of the auger housing on the machine and provides protection for the auger and the housing. If it is broken or not functioning properly, debris could damage these other parts of the snowblower. This would then require a larger repair.The shave plate is made from metal and is durable. However, the nature of the plate is to provide protection, which means it will become dinged and damaged over time. It could become bent if the user hits a large rock or chunk of ice. If there is damage to the snowblower shave plate, the user should be sure to replace it before using the machine again.This snowblower shave plate is compatible with models from Craftsman, MTD, White Outdoor, Ranch King, Yard-Man, and Yard Machines. The plate is sold individually, and it is a genuine OEM replacement part sourced from the manufacturer.

This genuine MTD shave plate, also known as a scraper bar, can be used as a replacement part for snowblowers. The shave plate is located at the bottom of the auger to scrape snow off of surfaces and filter it into the auger of the snowblower.Damage to the shave plate might include cracks, dents, and erosion to the metal material, or it can gradually wear out and no longer be effective. Evidence of a cracked shave plate can come from a visual inspection, but it can also be detected if the snowblower is doing a poor job of collecting and scraping snow off of surfaces. A cracked shave plate should be removed and replaced immediately, and a snowblower should not be used before the part is replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shave plate is compatible with the following brands: MTD, Yard Machines, Cub Cadet, Yard Man, and Craftsman. Part sold individually.

This blade adapter has a 25mm inner diameter and fits onto the blade of a variety of lawnmowers. The blade adapter allows the blade to connect to the spindle for proper performance. This blade adapter is made of metal. Regular wear and tear can cause the blade adapter to go bad or even split in half. When this happens, the blade adapter will need to be replaced.Before replacing the blade adapter, the lawnmower should be turned off and the spark plug wire needs to be disconnected. Turn the mower upside down to get access to the component. Use a socket set to remove the old blade adapter and replace it with the new component. Replace any other components, connect the spark plug wire, and test the machine before use. This component is sold on an individual basis. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The blade adapter is made to be used with lawnmowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This part is a shave plate. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a damaged, detached, or worn shave plate on certain models of snowblower. When using a snowblower, stubborn or stuck pieces of snow can affect proper functionality. Shave plates attach to the underside of the snowblower to help scoop stubborn snow or slush into the auger housing. Over time, as they regularly scrape the ground, shave plates will become worn and will no longer make sufficient contact with the pavement. In order to ensure snow blowers continue to do their job efficiently, shave plates should be replaced once they exhibit signs of deterioration. Proper tools are needed to replace this part and appropriate safety guideline should always be adhered to.As an authentic replacement part, this shave plate can be used on multiple different models of snow blowers manufactured by Cub Cadet, Craftsman, Huskee, Troy-Bilt, Yard-Man, and MTD. Please note that this shave plate is a genuine part made of high-quality, durable materials and is sold individually.