Bosch Dryer WTC82100SA Parts

Supports smooth drum rotation in your dryer. Replace if you hear squeaking, whistling, or rumbling during cycles. Verify fit with your model number.

Temperature monitoring sensor located in the dryer's heating system that regulates drying temperatures. Replace if clothes aren't drying properly, take too long to dry, or if the dryer overheats.

Replacement leveling foot for dryers. Installs on the bottom corner to elevate and stabilize the appliance. Order if cracked, broken, or missing.

Drive belt transfers power from motor to drum to tumble clothes. Replace if dryer drum won't turn or makes squealing noises. Confirm fit with your model.

This is a drum support roller that sits on an axle and helps the dryer drum rotate smoothly during operation. The roller bears the weight of the drum and its contents, reducing friction and noise. Replace this part if you hear thumping, squealing, or rumbling noises while the dryer is running, or if the drum no longer spins freely.

This is a heat exchanger filter assembly used in condenser dryers. It helps recover heat from the exhaust air and condense moisture so the dryer can operate without an external vent. Replace this part if drying times have increased significantly, the dryer is overheating, or the unit is not properly removing moisture from clothes.

Dryer won't start or door won't stay closed? This door latch assembly secures the door during operation, allowing cycles to run. Moderate DIY repair.

Dryer drum baffle lifts and tumbles clothes while circulating air evenly. Replace if cracked, loose, or causing noise. Verify fit with your model number.

This is a blower wheel that mounts inside the dryer's blower housing and circulates heated air through the drum during the drying cycle. It is driven by the drive motor and pushes air through the lint filter and exhaust vent. Replace this part if your dryer takes too long to dry clothes, makes squealing or rattling noises from the blower area, or fails to circulate air properly.

Dryer won't start or drum won't turn? A faulty motor assembly is often the cause. This part powers both the drum and blower. Moderate difficulty repair.

Fix a dryer making loud noises or not tumbling with a new drum. This part holds clothes during the drying cycle and may rust, dent, or crack over time.

Tension roller for dryers. Mounts to the support bracket to maintain proper belt tension around the drum. Replace if worn, squeaking, or damaged.

This is a replacement seal used to restore a watertight connection and help prevent leaks in compatible appliances. It provides a simple, low-cost way to replace a worn or damaged sealing element. What it does:

• Creates a secure, leak-resistant barrier at the mating surfaces where installed
• Helps stop visible leaks and drip symptoms associated with damaged seals
• Restores intended sealing performance when original gasket or seal is deteriorated

• Inspect mating surfaces for damage or debris and clean before installing the new seal
• Make sure the seal seats evenly and is fully inserted into its groove or recess
• Replace only with the correct OEM part number for a proper fit
• Disconnect power and water supply and follow appliance safety procedures before servicing

Replacement drum taper cone for your dryer. This structural component secures the drum assembly. Order a new taper if yours is cracked or damaged.

This replacement seal restores a tight, leak-resistant connection between mating components inside your appliance. Replacing a worn seal helps stop drips at the joint and keeps the system operating reliably without nuisance leak faults.

• Forms a compressible barrier between parts to prevent leakage at a connection point
• Helps protect nearby components from moisture intrusion and corrosion
• Typical failure signs: moisture around a joint, puddling beneath the unit, or leak/overflow error messages
• Replace if the original is cracked, flattened, cut, brittle, or missing

• Disconnect power and shut off the water supply before servicing
• Access the connection, note the seal's orientation, and remove the old seal
• Clean mating surfaces; lightly moisten the new seal and seat it evenly without twisting or pinching
• Reassemble and test for leaks before reinstalling covers or panels

Dryer not heating properly or overheating? This temperature sensor monitors heat levels to ensure safe, effective drying. Moderate DIY repair.