Gaggenau Range Hood AHS250161 Parts

Metal mesh filter captures grease and particles from cooking vapors. Replace when damaged or heavily soiled. Verify fit using your model number.

This part is the grease filter made to trap the grease from the exhaust air on an range hood. It is made out of metal mesh. It is important that this component is clean and clear for the range hood to operate at optimal levels. This product contains two filters.If the filter becomes clogged and cannot be cleaned with soap and water, then this will be a high-quality replacement part. Over time, the filter becomes dirt due to its function. If it begins to stink or become unsightly, the owner may wish to replace it. Doing so can often improve the overall performance of the oven hood.This particular set of grease filters is compatible with range hoods that have been manufactured by the Bosch and Maytag brands. This set is sold individually. It is sourced straight from the manufacturer as a genuine OEM part.

Reduces odors circulating in your range hood by trapping grease and food particles. Replace every 3-6 months for optimal air quality. Confirm fit with model.

This facia panel is the outer trim for the appliance's control area, restoring the finished look and protecting the underlying control components. It gives a clean appearance and helps keep controls secure and covered. What it does:

• Replaces a cracked, dented, scratched, warped, or otherwise damaged control-area facia
• Covers and protects the control components from spills, splashes and everyday wear
• Restores the appliance's finished front appearance and support for buttons/labels
• Helps prevent accidental button activation by keeping controls enclosed

• One facia panel as shown

• Disconnect power to the appliance before starting any work
• Installation typically requires removing trim/door screws and carefully prying off the old facia; keep screws and fasteners for reuse if undamaged
• Handle the new facia gently to avoid scratching the finished surface during installation
• Refer to your model-specific service manual for exact removal and reassembly steps

This is a replacement fluorescent lamp starter designed for use with 80W, 240V fixtures. It helps the lamp reach full brightness reliably so lighting cycles start and run normally. What it does:

• Provides the initial pulse to ignite fluorescent tubes in compatible fixtures
• Commonly restores lamps that fail to start or take multiple strikes to light
• Can stop or reduce continuous flickering or rapid flashing at startup
• Works with starter-type ballasts specified for 80W / 240V operation

• Disconnect power to the fixture before servicing to avoid shock
• Typically replaces a plug-in starter in the fixture's starter holder—pull old starter straight out and push the new starter into place
• Confirm fixture voltage and lamp wattage match the starter specifications before installing

Lamp window protects the internal bulb from grease and debris. Replace if cracked, discolored, or cloudy to restore proper lighting. Verify fit with your model number.

The range vent hood switch case houses the control switches for fan speed and lighting, located on the front of the hood. Replace when switches stick, don't click properly, or fan speeds and lights don't respond to switch positions.

This incandescent bulb cover protects the oven light bulb and helps keep the bulb clear of food debris while letting light into the oven cavity. It's a simple replacement to restore proper interior lighting and protection. What it does:

• Shields the incandescent oven light from splatter and direct contact
• Helps maintain clear, unobstructed interior lighting
• Replaces cracked, chipped or missing covers that expose the bulb
• Restores a safety barrier between the lamp and the oven cavity

• Disconnect power to the appliance and allow the oven to fully cool before servicing
• Use gloves or a cloth to avoid cuts from broken glass and to keep the cover clean
• Remove retainers or screws as needed, replace cover, then reinstall retainers securely

This is a front glass panel designed for a range vent hood. It serves as both a decorative cover and a protective window that allows light from the hood lamp to pass through. Replace this panel if it is cracked, chipped, or broken, or if it no longer fits securely in the hood frame.

This is a front-facing control panel for a range vent hood that houses the switches or buttons for fan speed and lighting. It mounts to the underside or front of the hood and provides the user interface for operating the ventilation system. Replace this panel if the buttons are broken, the panel is cracked or discolored, or if the controls no longer respond properly.

This is a replacement tension spring for AH 250/900 assemblies. It restores proper tension in the original mechanism so moving parts operate smoothly and reliably. What it does

• Provides tension for the AH 250/900 assembly so doors/closures move and return as designed
• Replaces a stretched, broken, or weak spring that can cause sagging or improper alignment
• Helps stop rattling or uneven movement caused by a failed spring
• Restores the original fit and function of the related hinge or mechanism

• Designed to install in the original spring location; confirm orientation before removing the old spring
• Use appropriate tools and take care to avoid pinching—springs can release tension suddenly
• Disconnect power or follow appliance-specific safety steps if working near electrical components