Gaggenau Range EB271610 Parts

This Halogen Bulb is an OEM part for Bosch Ranges. It provides illumination for the range's interior. Continuous use or high temperatures can cause the bulb to burn out or fail.

What Causes a Bad Halogen Bulb: 
Repeated heating and cooling cycles, along with continuous use, can cause the halogen bulb to burn out or break.

Symptoms of a Bad Halogen Bulb:

• The bulb is not lighting up
• Visible signs of damage or a broken filament
• Flickering or intermittent lighting

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is a sealing gasket designed to create an airtight fit on an oven or range component such as a door or lamp glass assembly. It prevents heat from escaping and protects internal parts from moisture and debris. Replace this seal if you notice heat leaking from the oven, uneven cooking temperatures, or visible wear and cracking on the existing gasket.

Fix an oven that won't heat to the right temperature or overheats food with this temperature sensor probe. Measures internal oven temp accurately.

This is a temperature limiter (thermoprotector) that acts as a safety device inside a microwave. It monitors internal temperatures and cuts power to the heating components if the appliance overheats, preventing damage or fire. Replace this part if the microwave shuts off unexpectedly during use, fails to heat, or if testing shows the limiter has tripped and no longer resets.

This inner door glass panel replaces a cracked, scratched or broken dishwasher door glass to restore the door's sealed surface and appearance. It provides a durable, smooth barrier that helps contain water and supports the door assembly. What it does:

• Replaces damaged or shattered inner door glass to restore door integrity and appearance
• Helps contain steam and water inside the tub by providing a smooth, sealed surface
• Reduces visible wear, scratches, and cosmetic defects on the dishwasher door
• Supports proper operation of the door assembly when installed correctly

• Disconnect power and water to the appliance before starting any repair.
• Handle glass with heavy-duty gloves and eye protection; glass can break and cause injury.
• Installation typically requires removing the outer door panel and fasteners; follow the OEM service instructions for your model.

A female door latch that secures the appliance door and ensures a proper close for safe operation. Replaces a worn or broken latch to restore reliable door engagement and help the appliance start normally. What it does:

• Secures the door by engaging the corresponding door striker so the appliance can run
• Helps prevent the door from popping open during operation
• Commonly replaced when the door won't stay closed or the unit displays a "door"/won't-start symptom
• Fits the OEM latch location and mates with the matching male striker to restore proper function

• One female door latch

• Disconnect power (and gas, if applicable) before servicing
• Remove the outer door panel or access panel as required to reach the latch assembly
• Align the latch with the striker and secure fasteners; test door engagement before reassembly

This oven temperature probe is the internal sensor that monitors cooking cavity temperature so the oven control can regulate heat for accurate cooking and bake results. It's a direct-replacement sensing probe for compatible Bosch ovens. What it does:

• Measures internal oven temperature and sends readings to the control board
• Allows the oven to maintain set temperatures for consistent cooking
• Common symptoms of a failing probe: inaccurate oven temps, oven not reaching set temperature, or temperature-related error codes
• Works with the oven's control system to help cycle heating elements or gas valve

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle the probe and its wiring gently; avoid sharp bends or pulling on connectors
• Verify connector orientation and secure connections to the control board per OEM diagram

This is a glass panel that serves as part of the control panel area on a range or oven, covering and protecting the controls while allowing visibility of indicators and displays. It provides a smooth, finished surface on the front of the appliance. Replace this panel if it is cracked, chipped, shattered, or if the surface has become cloudy or damaged from heat exposure.

This inner door seal replaces the gasket that fits along the inside edge of the appliance door, helping restore a watertight and airtight closure for proper operation and cleaning. It's a direct-fit part for affected door assemblies. What it does

• Forms a sealed barrier between the door and tub to prevent leaks during cycles
• Restores proper door closure and helps maintain internal temperature and pressure
• Can reduce moisture build-up and visible drips around the door edge
• Helps prevent damage to cabinetry and flooring from escaping water

• One inner door seal (single gasket piece)

• Inspect the door and surrounding trim for damage; replace any broken retainers before installing the seal
• Clean the gasket channel and mating surfaces, then press the new seal evenly into the groove until fully seated
• Use caution to avoid sharp edges; wear gloves and follow manufacturer safety guidance

This selector switch module is the user-control assembly that lets the appliance register and change program selections. It restores reliable input from the front control to the main electronics for accurate cycle selection and operation. What it does:

• Routes user selections from the control panel to the appliance control board
• Enables program or mode changes when the front-panel dial/selector is used
• Replaces a worn or unresponsive selector to restore consistent control input
• Addresses symptoms like unresponsive controls, intermittent selection changes, or failure to switch programs

• Disconnect power before starting any repair to avoid shock or damage
• Handle the module and surrounding electronics gently; avoid static discharge
• Installation typically requires removing the control panel and mounting screws; keep fasteners and wiring organized