Gaggenau Range EB388210 Parts

This Halogen Bulb is an OEM part for Bosch Ranges. It provides illumination for the range's interior. Continuous use or high temperatures can cause the bulb to burn out or fail.

What Causes a Bad Halogen Bulb: 
Repeated heating and cooling cycles, along with continuous use, can cause the halogen bulb to burn out or break.

Symptoms of a Bad Halogen Bulb:

• The bulb is not lighting up
• Visible signs of damage or a broken filament
• Flickering or intermittent lighting

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door hinge provides the pivot point that lets the appliance door open smoothly and close flush. Replacing a worn or bent hinge restores proper alignment and sealing for safe, reliable door operation.

• Provides the pivot point that guides door opening and closing
• Helps keep the door square to the cabinet for a consistent seal
• Wear or damage can cause sagging, binding, gaps, or a door that won't close flush
• Restores smooth movement and proper door alignment

• Disconnect power before servicing; also shut off gas or water
• Support the door during removal to prevent damage or injury
• Transfer any mounting screws/brackets from the old hinge to the new one
• After installation, verify door alignment and gasket contact; adjust as needed

Seals side lamp glass on lawn tractors, blocking moisture and debris from the housing. Replace when glass rattles or leaks occur. Confirm fit with your model.

This oven temperature probe is the internal sensor that monitors cooking cavity temperature so the oven control can regulate heat for accurate cooking and bake results. It's a direct-replacement sensing probe for compatible Bosch ovens. What it does:

• Measures internal oven temperature and sends readings to the control board
• Allows the oven to maintain set temperatures for consistent cooking
• Common symptoms of a failing probe: inaccurate oven temps, oven not reaching set temperature, or temperature-related error codes
• Works with the oven's control system to help cycle heating elements or gas valve

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle the probe and its wiring gently; avoid sharp bends or pulling on connectors
• Verify connector orientation and secure connections to the control board per OEM diagram

This control panel lens cover protects the oven's display and touchpad area from spills, scratches and everyday wear while keeping the display visible and looking finished. It restores the appliance's appearance and helps prevent damage to the underlying controls. What it does

• Shields the display and control buttons from food splatter, grease and scratches.
• Keeps the display readable by reducing direct contact and surface damage.
• Replaces cracked, chipped or yellowed lens surfaces that obscure the control panel.
• Helps prevent moisture from directly contacting the control electronics when properly seated.

• One lens cover for the control panel.

• Disconnect power to the appliance before starting any work.
• Typically installs by removing the control panel trim or bezel; handle the lens by the edges to avoid fingerprints.
• Inspect mounting tabs or clips for damage and align carefully before snapping or fastening into place.
• If screws or additional trim are required, reuse OEM fasteners.

Control module not responding or cycles won't start? This electronic control board restores cycle control and user-interface functions. Moderate DIY repair.

Replace a bent, warped, or missing oven rack. This wire shelf installs inside your oven to provide stable support for cookware and bakeware at the correct height.

Seals the engine compartment door on your lawn tractor to keep out debris and moisture. Replace if torn, cracked, or no longer sealing properly.

Oven not heating properly or temperature way off? This temperature sensor probe accurately monitors cavity temperature for reliable cooking. Straightforward fix.

This halogen bulb socket connects and secures the oven light bulb so the interior light works reliably when the door is opened or the light switch is used. Replaces a worn or damaged socket to restore a solid electrical connection. What it does:

• Holds the halogen oven light bulb in place and provides the electrical contacts to power the lamp
• Commonly used when the oven light flickers, won't turn on, or the bulb becomes loose
• Maintains correct alignment and insulation for safe bulb operation
• Designed for direct replacement of the original socket in compatible ovens

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Allow the oven and bulb to cool completely before touching components
• Handle halogen bulbs with a clean cloth or gloves; oils from skin can shorten bulb life

If your cooktop burner won't turn on or off properly, a faulty switch is often the cause. This replacement switch restores control to your cooktop.

Light socket for your range. Installs in the oven cavity or cooktop area to hold the interior light bulb. Replace if cracked, damaged, or no longer secure.

This safety device monitors oven temperature and shuts off heating elements if temperatures exceed safe limits. Replace when oven overheats, fails to reach proper temperatures, or heating elements cycle on and off erratically.