Gaggenau Freezer RF413301 Parts

This slide rail retainer secures the freezer drawer or shelf rails in their proper position within your freezer compartment. It prevents the rails from shifting or coming loose during normal use of the drawer system. Replace this part if your freezer drawer doesn't slide smoothly, falls off its track, or if the rails have become loose or misaligned.

Secures freezer baskets to drawer rails in your refrigerator. Replace if clip is cracked, broken, or missing to keep bins properly mounted and stable.

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

This is a replacement micro switch used in select Bosch-built appliances. It opens and closes an electrical circuit when actuated by a lever or cam, enabling functions like starting/stopping a cycle or detecting a position.

• Controls power or signals by opening/closing a low-voltage circuit when pressed
• Commonly used for on/off, door/lid, or position-sensing functions
• Failure may cause the unit not to start, intermittent operation, or features that won't engage
• May also present as unresponsive buttons or functions that only work when pressed a certain way

• Disconnect power before servicing; verify no voltage is present
• Access location varies by model; remove panels as needed to reach the switch
• Note wire positions and terminal orientation before removal
• Test continuity with a meter after installation to ensure proper operation

Leveling foot installs at the refrigerator base to support and level the unit. Replace if worn, cracked, broken, or missing to restore stability.

Mounting hardware kit secures refrigerator components in place. Replaces worn, missing, or damaged fasteners that cause rattling or loose parts inside unit.

This hinge pin secures the door hinge mechanism and allows your refrigerator or freezer door to pivot smoothly. It maintains proper door alignment and prevents the door from sagging or binding. Replace this part if your door won't close properly, sags when opened, or if you hear squeaking or grinding when opening the door.

Trim strip that provides a finished edge and protective cover at its mounting location. Replace when cracked, worn, or missing to restore proper appearance.

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

Fixes unresponsive controls, display errors, or cycle failures in refrigerators and freezers. Direct replacement for failed main control modules.

The FIXTURE is an OEM component specifically designed for Bosch refrigerators. Typically located inside the fresh food compartment, fixtures hold slidable wire shelves, bins, crispers, and other removable storage accessories in precise positions.

Causes of a faulty fixture can include cracking or breaking of plastic rails from repeated impact or overloading. Clips and mounting attachments may also loosen over time.

Symptoms of a bad fixture include: 

• Shelves, bins, and pans that no longer slide smoothly or feel insecure
• Storage accessories like crispers that tilt or are difficult to remove
• Interior rattles or banging noises coming from loose components

This replacement Bosch fixture returns stability and structure to the organization system. Realigning fixtures maintains consistent placement and secure engagement of accessories for tidy, accessible food storage. 

Compatible with Thermador, Gaggenau, or Kenmore French door models utilizing consistent interiors.

This is a replacement dryer complete assembly designed to restore drying function and structure for compatible Bosch laundry units. It provides the main cabinet and drum enclosure needed for normal tumbling and airflow. What it does

• Houses the drum and internal components so clothes can tumble during the drying cycle
• Provides the enclosure and mounting points for the blower, heating system, and controls
• Restores proper airflow pathways to help the dryer heat and vent as intended
• Helps eliminate issues caused by damaged or severely warped cabinet or drum housings

• One complete dryer assembly as shown

• Disconnect power before servicing
• Follow factory service manual for alignment, seal, and vent reconnection steps
• Inspect and replace any worn seals, ducts, or mounting hardware as needed during installation

Decorative trim piece that covers the exposed door edge or seam on your refrigerator. Replace when cracked, peeling, or missing to restore the finished look.

The Installation Set is an OEM part for Bosch refrigerators. It includes the necessary parts for installing or replacing the evaporator assembly in your refrigerator.

A bad installation set can occur due to wear and tear, refrigerant leaks, or damage from external factors. Signs of a faulty assembly include inadequate cooling, frost buildup, or strange noises coming from the refrigerator.

Symptoms of a bad installation set include:

• Inadequate cooling 
• Excessive frost or ice buildup on the evaporator coil
• Unusual noises coming from the refrigerator

Replace your damaged or malfunctioning installation set with this genuine OEM Bosch part to restore your refrigerator. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

This rack wheel lets your dishwasher rack glide smoothly along its rails. Replacing a worn, cracked, or missing wheel restores easy in-and-out movement and helps keep the rack properly supported during loading and unloading.

• Mounts to the rack/rail to support and guide the rack
• Allows the rack to roll smoothly on the track
• Helps prevent sticking, wobbling, or the rack jumping off the track
• Common symptoms: hard-to-slide rack, wheel damage, or rack derailing

• Unplug the dishwasher. Turn off water supply.
• Pull the rack out; release the old wheel from its clip/fastener.
• Attach the new wheel in the same position and ensure it spins freely.
• Reinstall the rack and test for smooth travel.