Kenmore Range Hood 233.5188911 (2335188911, 233 5188911) Parts

The Damper is an OEM part for Broan range hoods. It is designed to regulate airflow, preventing backdrafts and ensuring efficient ventilation by allowing air to flow out while blocking external air from entering.

Causes of a bad damper can include accumulation of grease or debris, damage from cleaning or impact, or wear and tear over time. A malfunctioning damper can lead to poor ventilation and compromised kitchen air quality.

Symptoms of a bad Damper include:

• Reduced airflow or ventilation efficiency
• Unusual noises from the range hood
• Odors lingering in the kitchen
• Air drafts entering through the range hood

This OEM Broan part is designed for optimal performance, helping maintain a clean and well-ventilated kitchen environment.

This replacement range hood filter maintains airflow and helps keep the cooking area cleaner by capturing airborne grease and particulates drawn through the hood. Replace when saturated or damaged to keep your hood performing as intended.

• Filters air drawn through the hood to trap grease and cooking byproducts
• Helps maintain consistent airflow and capture of smoke/steam
• Common replacement signs: heavy grease buildup, reduced ventilation performance, or a warped/loose filter
• Protects the blower and ducting by preventing debris from entering

• Disconnect power to the hood and allow all surfaces to cool; sheet-metal edges can be sharp—wear gloves
• Release the filter latch or tabs and slide out the old filter
• Install the new filter with the tab/latch oriented correctly; ensure it seats fully
• Restore power and verify the filter is secure and airflow is unobstructed

This replacement motor drives the blower in your ventilation fan or hood to restore proper airflow and dependable operation. Install it to fix a fan that hums, stalls, or runs loudly due to a failing motor.

• Powers the blower wheel to move air through the duct system
• Restores airflow when the original motor is weak, seized, or intermittently stopping
• Addresses symptoms like humming, slow start, overheating/shutoff, or reduced airflow
• Can reduce excessive noise caused by worn bearings or a dragging rotor

• Disconnect power at the breaker before servicing
• Support the grille/cover and remove the fan housing or access panel as required by your model
• Transfer the existing fan blade/wheel and any mounting hardware to the new motor in the same orientation
• Spin the wheel by hand to check clearances; restore power and test before final reassembly

This replacement fan blade restores airflow in hood and ventilation blowers by moving air through the fan assembly. Use it to replace cracked, bent, or worn blades and help reduce vibration and noisy operation. What it does:

• Spins on the blower motor to generate airflow for ventilation and exhaust.
• Replaces blades that are cracked, bent, or visibly damaged and causing reduced airflow.
• Can reduce unusual noise and vibration caused by an imbalanced or broken blade.
• Helps restore proper vent performance when airflow is weak or inconsistent.

• Disconnect power to the appliance before starting any service.
• Remove the blower housing or access panel to reach the blade; follow OEM instructions.
• Keep fasteners and spacers in order during disassembly; reassemble with original hardware unless replacements are specified.
• If vibration or noise persists after replacing the blade, inspect motor bearings, mountings, and blower housing for damage.

This retainer is a small mounting clip used in Broan ventilation hoods to hold trim, lenses, or small assemblies securely in place. Replacing a worn or broken retainer restores stable mounting and reduces vibration or rattling. What it does:

• Secures trim pieces, light lenses, or small assemblies so they stay aligned and seated
• Prevents parts from shifting or vibrating during operation
• Helps stop rattling or loose components around the hood opening
• Keeps replaceable covers and lenses from falling out when installed correctly

• Disconnect power to the appliance or turn the circuit breaker off before working on the hood
• Use common hand tools as needed; handle sharp sheet-metal edges with gloves
• Verify this retainer matches the damaged piece before installation

This socket is the lamp holder designed to secure and connect a light bulb to the appliance, restoring reliable illumination. It provides the physical and electrical connection needed for compatible appliance lamps. What it does:

• Holds the light bulb securely and provides the electrical contacts for operation
• Restores lighting when a damaged or worn socket causes flickering or no light
• Compatible with standard appliance lamp replacements that match the original socket type
• Helps maintain proper bulb alignment for reflectors and filters to work as intended

• Disconnect power to the appliance before beginning any work to avoid electrical shock
• Inspect wiring and connectors for damage; replace if frayed or corroded
• Reinstall bulb and any removed trim or housing panels securely before restoring power

This is an electrical wire lead used to restore or replace a damaged connection in the appliance. It provides a direct conductive path so motors, lights, or controls can receive power and signals reliably. What it does:

• Reconnects power or signal between components when the original wire is damaged or broken
• Restores functionality for motors, fans, lights, or switches that are losing power due to a faulty lead
• Prevents intermittent operation caused by frayed, corroded, or cut wiring
• Helps maintain safe electrical continuity when properly installed and secured

• One wire lead

• Disconnect mains power before inspecting or replacing wiring to avoid shock or injury
• Match wire color, connector type, and routing to the original; use proper crimps/terminals or solder and insulated sleeving
• Secure wire away from moving parts and heat sources; replace any damaged insulation or clips

Color: white.

A replacement rocker-style switch that restores on/off control for range hood lights or fans, helping fix loss of power or intermittent operation. Simple direct-fit design for easy swap-out and reliable everyday use. What it does

• Provides on/off control for hood lights or blower motors where the original rocker switch failed
• Replaces a worn, stuck, or non-responsive rocker to restore consistent power
• Commonly used when lights won't turn on, fan won't start, or operation is intermittent
• Handles user input with a tactile rocker action for straightforward operation

• One rocker-style switch

• Disconnect power to the appliance at the breaker before servicing
• Remove the hood/light housing per the appliance service instructions to access the switch
• Note wire locations or take a photo before disconnecting leads to ensure correct reconnection

This is a replacement mounting nut used to secure components and hardware in range hoods and ventilation assemblies. It provides a simple, reliable fastener to hold studs, bolts, or threaded posts in place. What it does:

• Secures panels, mounting brackets, or trim pieces to threaded studs or bolts
• Helps keep components aligned and prevents parts from slipping loose
• Can be used where a small, standard nut is required for assembly or repair
• Commonly replaced when stripped, corroded, or missing to restore safe attachment

• Disconnect power to the appliance and ensure the area is safe before servicing
• Match nut to the correct stud/bolt thread size and pitch before installation
• Tighten with the appropriately sized wrench; avoid over-tightening which can strip threads
• Replace any damaged mating hardware for a secure fit

This black name plate restores the appliance's factory ID and appearance where the original plate is worn, faded, cracked or missing. A direct-fit cosmetic replacement that helps make the unit look finished and correct. What it does:

• Replaces a damaged or missing name plate to restore the appliance's exterior appearance
• Provides the original mounting location for labels, model/serial information or branding as intended by the manufacturer
• Helps maintain resale value and a factory-fresh look for the appliance
• Prevents exposed mounting holes or rough edges where the original plate was removed

• One black name plate replacement

• Follow the appliance manufacturer's service instructions for removal and replacement of the name plate
• Disconnect power to the appliance or take other appropriate safety precautions before accessing panels
• Use the original mounting hardware when possible; replace with equivalent fasteners approved for the appliance
• Handle edges carefully during install to avoid cuts or damage to surrounding surfaces

This mount is the replacement mounting bracket that secures range hood/ventilation components to the cabinet or chassis, restoring proper support and alignment for safe operation. What it does:

• Provides a secure attachment point for the hood or internal parts to prevent sagging or movement
• Helps maintain correct alignment for ducting and components to reduce vibration and noise
• Replaces damaged, bent, or corroded mounting hardware that can compromise fit and stability
• Commonly used when the hood shifts, sits unevenly, or produces rattling during use

• Turn off power to the appliance at the breaker before beginning any work
• Use appropriate screws/fasteners and torque to OEM recommendations; replace any stripped hardware