Kenmore Range Hood 233.5217811 (2335217811, 233 5217811) Parts

The Damper is an OEM part for Broan range hoods. It is designed to regulate airflow, preventing backdrafts and ensuring efficient ventilation by allowing air to flow out while blocking external air from entering.

Causes of a bad damper can include accumulation of grease or debris, damage from cleaning or impact, or wear and tear over time. A malfunctioning damper can lead to poor ventilation and compromised kitchen air quality.

Symptoms of a bad Damper include:

• Reduced airflow or ventilation efficiency
• Unusual noises from the range hood
• Odors lingering in the kitchen
• Air drafts entering through the range hood

This OEM Broan part is designed for optimal performance, helping maintain a clean and well-ventilated kitchen environment.

This replacement knob restores a clean look and reliable control of your unit's settings. It fits onto the control shaft to give you a secure, easy-to-grip dial when the original knob is cracked, loose, or missing.

• Press-fits onto a control shaft to operate the switch or speed control
• Provides a secure grip for selecting settings as intended
• Replaces damaged, cracked, or missing knobs
• Helps address slipping, free-spinning, or hard-to-turn controls

• Disconnect power to the appliance before servicing
• Pull the old knob straight off; avoid prying against the panel to prevent damage
• Align the flat/D-shaped insert with the shaft and press on until fully seated
• Restore power and test operation

This scroll is the blower housing that directs airflow inside the ventilation blower assembly, restoring proper exhaust flow and helping reduce noise from an unstable blower. It fits into the blower motor assembly to channel air through the fan. What it does:

• Channels and directs airflow from the blower wheel to the exhaust duct
• Helps position and support the blower wheel for stable operation
• Worn or damaged scrolls can cause reduced airflow or poor exhaust performance
• Cracks, deformation, or loose fit may create vibration or unusual noise

• Disconnect power to the appliance before any service to prevent electrical hazard
• Installation typically requires removing the blower assembly and a few fasteners; keep track of screws and orientation
• Inspect the blower wheel and motor during reassembly; replace any damaged components
• Handle edges carefully and test operation after installation to confirm airflow and quiet operation

This is a replacement control switch that restores on/off and setting control for your ventilation appliance. It provides a direct, user-facing interface to operate a blower or light from the cooker hood or ventilation unit. What it does:

• Serves as the user control for turning the blower or light on and off
• Switches between available operating settings so the appliance responds to user input
• Replaces a worn, stuck, or non-responsive control to restore normal function
• Fits into the original switch location and connects to the factory wiring

• Disconnect power to the appliance at the breaker before starting any work.
• Handle wiring carefully; match wire colors/terminals exactly and secure all connections.
• If the switch is mounted behind trim or a fascia, remove those parts gently to avoid damage.

This electronic control module operates the hood's fan and lights so the range hood responds to user commands and runs reliably. Replaces a failed or unresponsive control to restore normal vent and lighting operation. What it does:

• Receives input from the hood's buttons or touchpad and activates fan speeds and lights
• Controls power to blower motor and lighting circuits based on user selections
• Can resolve symptoms like unresponsive controls, intermittent fan/lights, or loss of specific speed settings
• Works as the main interface between user controls and the hood's electrical components

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the module carefully; avoid bending pins or exposing it to static
• Typical install requires removing the hood's access panel and unplugging the old module connector(s)
• Test all functions after installation and secure panels before returning the hood to service

This is a replacement mounting nut used to secure components and hardware in range hoods and ventilation assemblies. It provides a simple, reliable fastener to hold studs, bolts, or threaded posts in place. What it does:

• Secures panels, mounting brackets, or trim pieces to threaded studs or bolts
• Helps keep components aligned and prevents parts from slipping loose
• Can be used where a small, standard nut is required for assembly or repair
• Commonly replaced when stripped, corroded, or missing to restore safe attachment

• Disconnect power to the appliance and ensure the area is safe before servicing
• Match nut to the correct stud/bolt thread size and pitch before installation
• Tighten with the appropriately sized wrench; avoid over-tightening which can strip threads
• Replace any damaged mating hardware for a secure fit

This replacement name plate restores the original identification label and appearance on compatible Broan products. It helps keep model/serial info visible and maintains a finished look where the original plate is missing or damaged. What it does:

• Replaces a missing or damaged identification label so appliance information is visible
• Restores finished appearance to the appliance's exterior
• Helps ensure model and serial details remain legible for service or warranty needs
• Simple cosmetic part—does not affect appliance operation

• Clean and dry the mounting area before installation for best adhesion or fit
• Align carefully and press into place; if fasteners are used, secure with the original hardware
• Avoid placing over vents, moving parts, or controls