Kenmore Air Conditioner 253.70101012 (25370101012, 253 70101012) Parts

This window filler kit installs on the sides of a window air conditioner to close gaps between the chassis and the window frame. It helps secure the unit and limit air leaks, moisture, and pests from entering the room.

• Closes the left and right side openings between the unit and sash window
• Helps stabilize the air conditioner and reduce vibration noise
• Replaces cracked, brittle, warped, or missing side curtains/fillers
• Common signs: drafts or visible gaps around the unit; torn or broken accordion panels

• Disconnect power and support the air conditioner to prevent a fall
• Slide the fillers into the unit's side channels or mounting frames per your model's instructions
• Reuse the unit's hardware as directed; avoid overtightening fasteners in plastic components
• After installation, ensure the unit is secured and pitched for proper drainage per manufacturer guidance

Replacement evaporator fan blade that moves cold air across the evaporator coil and through the refrigerator compartments to help maintain even temperatures. Restores airflow to reduce warm spots and improve overall cooling consistency. What it does:

• Spins on the evaporator fan motor to circulate cold air through the freezer and fresh-food sections.
• Restores proper airflow when the original blade is cracked, warped, or broken.
• Common symptoms prompting replacement: reduced or uneven cooling, rattling/scraping noises from the freezer, or visible blade damage.
• Helps prevent excessive frost buildup by maintaining steady airflow over the evaporator.

• Disconnect power to the appliance before beginning any service.
• Handle the blade carefully; edges and broken pieces can be sharp.
• Ensure the blade is fully seated on the motor shaft and any retaining hardware is reinstalled per the OEM's guidance.

This retainer secures a mating component in your appliance so it stays properly aligned during use. Replacing a damaged or missing retainer restores a snug fit, reduces vibration noise, and helps prevent the attached part from shifting or falling.

• Secures the attached part to prevent movement and vibration
• Maintains proper alignment and fit within the assembly
• Failure clues: attached component is loose, rattles, sags, or won't stay in place
• Visual signs: retainer is cracked, deformed, worn, or missing

• Disconnect power to the appliance before starting; allow hot or moving parts to cool/stop
• Note the original orientation and position; take a quick photo for reference
• Seat the new retainer fully and transfer any original fasteners as needed
• Do not overtighten hardware; verify the held component is secure before reassembly

This handheld remote control sends wireless commands to your appliance so you can change settings from a distance. It replaces a lost or non-working remote to restore convenient, button-based control of functions and modes. What it does:

• Sends infrared/wireless signals to the appliance receiver to change settings
• Lets you adjust common functions such as power, mode and temperature/fan settings
• Restores remote operation when the original remote is lost, damaged or unresponsive
• Resolve issues where the appliance doesn't respond to remote commands

• Install fresh batteries before first use and after long storage; use correct battery type
• Point remote at the appliance receiver and test from several feet away; remove obstructions
• If the appliance doesn't respond, check receiver/IR sensor and power to the appliance
• Handle electronic parts carefully; disconnect power to the appliance before servicing internal components

This replacement power cord restores AC power to compatible refrigerators by replacing a damaged or worn supply lead. It provides a direct, safe power connection so the appliance can run reliably. What it does:

• Replaces a frayed, cut, or otherwise damaged power supply cord
• Restores consistent power when the appliance will not turn on or has intermittent power
• Maintains the appliance's grounding connection for safe operation
• Prevents electrical arcing from exposed wiring or compromised insulation

• One replacement power cord

• Disconnect the appliance from the power source before inspecting or replacing the cord
• Install with the proper strain relief and secure fasteners to prevent pinching or pull-out

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a failed thermistor restores accurate temperature readings for more consistent fridge and freezer performance. What it does:

• Senses internal air temperature and sends that information to the control board
• Helps the defrost and compressor cycles run at the correct times
• Commonly linked to symptoms like inconsistent temperatures, error codes, or a unit that runs constantly
• Does not control cooling directly but provides the temperature feedback the system needs

• Always disconnect power to the appliance before beginning service
• Typically located in the fresh food or freezer compartment near the evaporator
• Handle the sensor and wiring gently; avoid pulling on the wires or bending the probe sharply
• If troubleshooting, verify wiring and sensor resistance per the manufacturer's service instructions before replacement

This electronic control is the user interface and control board that manages oven functions, timers and temperature regulation to restore responsive controls and proper cooking cycles. Fits as the direct replacement control assembly. What it does:

• Replaces a faulty oven control board to restore display, keypad and timed functions.
• Manages temperature setpoints, bake/broil cycles and timed cooking operations.
• Commonly used when the display is blank, buttons are unresponsive, or oven fails to heat properly.
• Interfaces with sensors, switches and relays to coordinate heating elements and fans.

• Disconnect power to the appliance before servicing to avoid shock risk.
• Handle the board by its edges; avoid touching components and connectors to prevent ESD damage.
• Verify connector orientation and secure all fasteners; ensure wiring harnesses are fully seated.

This cabinet is the outer housing panel that supports and protects the appliance's internal components while restoring the unit's appearance and structure. Use it to replace a damaged, dented, or corroded outer shell. What it does

• Replaces the appliance's outer housing to restore structural support and protect internal parts.
• Covers internal wiring, controls, and insulation to prevent exposure and debris entry.
• Stops drafts, gaps, or misalignment caused by bent or damaged exterior panels.
• Improves appearance by replacing dented, scratched, or corroded surfaces.

• One cabinet (outer housing) as shown.

• Disconnect power (and fuel supply if applicable) before beginning any repair.
• Removal typically requires removing trim, panels, and fasteners—keep hardware organized for reassembly.
• Be careful of sharp edges on metal panels; wear gloves and eye protection.

A replacement start/run capacitor that helps the refrigerator's motor(s) get up to speed for reliable cooling and circulation. Restores proper motor starting when the original capacitor has failed. What it does:

• Provides the electrical boost needed for compressor and fan motors to start and run smoothly
• Commonly replaced when motors hum, fail to start, or fridge cooling is inconsistent
• Helps prevent motor overloads and repeated hard-start cycling when functioning correctly
• Matches the original part's role in the appliance's electrical starting circuit

• Disconnect power to the appliance at the breaker before servicing
• Discharge the capacitor before touching terminals to avoid shock; use insulated tools
• Verify terminal orientation and secure wire connections; do not force fit