Bosch Freezer KAN62A75 Parts

Replaces a cracked, broken, or missing refrigerator door bin tray. Restores secure storage for bottles and items in the door compartment.

Rubber foot that cushions and stabilizes your refrigerator, preventing sliding and surface scratches. Replace if worn, cracked, or missing.

Supports the refrigerator door hinge for smooth, quiet opening and proper alignment. Replace if door catches, squeaks, or binds. Verify fit with your model.

Fix a warm fridge or freezer alarm with this temperature sensor. Replaces faulty thermistors causing incorrect temperature readings and food spoilage.

This drain gutter is the molded channel that collects and directs wash water toward the dishwasher drain, helping prevent pooling at the tub base and under the door. It restores proper water flow inside the lower tub area. What it does:

• Channels leftover wash and condensation to the pump/drain to avoid water buildup under the door
• Helps reduce leaks and water pooling at the bottom front of the tub
• Replaces cracked or warped gutters that cause misdirected drainage or visible water inside the door area
• Matches OEM shape so water follows the intended path to the drain system

• One drain gutter

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door or lower access panel per the service instructions to reach the gutter
• Handle carefully to avoid damage to the molded edges and to prevent contact with sharp cabinet or panel edges
• Secure mounting so the gutter seats fully to the tub and mates properly with adjacent seals

The adjusting screw allows you to level your refrigerator and adjust door alignment, typically located at the base of the unit. Replace when the screw becomes stripped, corroded, or can no longer properly support or adjust the refrigerator.

This door seal fits around the dishwasher tub opening to keep water and steam inside during cycles. Replacing a worn gasket restores a tight seal so the door latches properly and helps prevent leaks at the sides or bottom.

• Creates a watertight barrier between the door and tub during wash and rinse cycles
• Helps contain steam and reduce moisture escaping from the front of the unit
• Replaces a flattened, cracked, torn, or deformed seal that can cause leaks
• Common symptoms include drips at the front edge, water on the floor near the door, and needing extra force to latch

• Disconnect power and, if applicable, shut off the water supply before servicing
• Pull the old seal from the channel; clean the groove and mating surfaces thoroughly
• Press the new seal in evenly without stretching; seat corners fully and position the joint at the bottom center
• Close the door to help the seal set; a snug fit at first is normal

This is a flexible rubber seal that attaches around the perimeter of the freezer door, creating an airtight closure when the door is shut. It prevents warm air from entering the freezer compartment and keeps cold air from escaping. Replace this gasket if you notice frost buildup inside the freezer, the door does not seal tightly, the gasket is torn or warped, or the compressor runs more frequently than normal.

This is an electrical on/off switch used to control power to an appliance circuit. It replaces a failed switch so controls respond normally and the appliance can be powered on and off safely. What it does

• Opens and closes an electrical circuit to enable or disable appliance power or a specific control function
• Commonly replaces a worn, stuck, or unresponsive switch that prevents controls or lights from operating
• Can resolve symptoms like no power to a control, intermittent operation, or a button that won't actuate
• Designed to mate with the appliance's existing wiring and mounting points

• One electrical on/off switch

• Disconnect power to the appliance at the breaker or unplug before working on wiring
• Verify proper wire locations and secure all terminal connections; replace only with the exact part specified by the manufacturer
• Handle the part carefully to avoid bending terminals or damaging the switch actuator

Replacement interior tray for your refrigerator. Restores a flat, stable surface for holding items. Replace if cracked, broken, or missing.

Secures the right-side door track assembly for smooth operation and proper alignment. Replace if cracked, broken, or missing to restore panel fit.

Replacement door stop for your refrigerator. Installs on the door or cabinet to prevent damage. Order a new stop if yours is broken, cracked, or missing.

This replacement utensil tray holds silverware and small kitchen tools in the dishwasher, keeping items separated for better cleaning and preventing nesting. It restores secure, organized loading for consistent wash results. What it does:

• Provides a dedicated space for forks, knives and spoons to keep items upright and separated
• Helps prevent flatware from nesting so water and detergent reach all surfaces
• Fits into the dishwasher rack to stabilize small items during the wash cycle
• Reduces movement and rattling of utensils while the dishwasher runs

• Slide or clip the tray into the designated position in the dishwasher rack; no tools typically required
• Inspect for wear or broken clips and replace the rack or mounting hardware if needed
• For safety, disconnect power to the appliance before attempting repairs that require moving the rack assembly

Replace your refrigerator's back panel if it's cracked, damaged, or missing. This structural component covers the rear interior compartment wall.