Bosch Cooktop NGMP056UC Parts

Fix burners that won't light or spark constantly with this spark module. Generates high-voltage pulses to ignite surface burners. Moderate DIY repair.

Replacement rubber feet for gas cooktop grates. Kit includes 4 feet and adhesive. Needed when original feet are cracked, worn, missing, or fell off.

Weak or fluttering flames on multiple burners? Your gas pressure regulator stabilizes fuel supply to ensure consistent flame performance across all burners.

Secures your cooktop to the countertop from below. Includes brackets and hardware. Replace if worn, deformed, or screws are damaged or missing.

Foam seal tape creates a tight seal between your cooktop and countertop to contain spills and provide heat isolation. Replace when adhesive weakens.

Replace your gas cooktop burner cap if flames are uneven or heat isn't distributing properly. Fits specific Bosch models. Easy 5-minute swap.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

Replace a cracked or warped burner that won't heat evenly or maintain temperature. Compatible with select gas cooktop models. Moderate DIY repair.

Cast iron grate set for left, center, and right burner positions. Replace cracked, damaged, or missing grates to restore stable cookware support.

Replace a cracked or warped burner cap causing uneven flames or yellow flame color. Sits atop the burner to distribute heat evenly during cooking.

The Gas Valve is an OEM component specifically designed for Bosch ranges and cooktops. It controls the flow of gas to the burners, maintaining a consistent flame for safe and efficient cooking performance. 

Causes of a bad gas valve can include mechanical failure over time, blockages due to contaminants, or issues with the electronic igniter or control board. 

Symptoms of a bad gas valve include:

• Inability to light or control burner flames 
• Flames that fluctuate between large and small sizes
• Burners that will not light at all
• Gas smell near the range
• Pilot lights that keep going out

This Bosch gas valve replacement part is also compatible with some Thermador, Gaggenau, Dacor, and Broan-NuTone brands. Replacing the defective component restores the appliance's heating function.

This is a gas valve used on a cooktop to control the flow of gas to a burner. It regulates the gas supply when you turn the burner knob, allowing you to adjust the flame from low to high. Replace this valve if a burner won't ignite, the flame is uneven or won't adjust properly, or you detect a gas smell when the knob is in the off position.

This surface burner head replaces a worn or damaged burner on compatible gas cooktops, restoring even heat and reliable flame distribution so pots and pans heat more consistently. What it does:

• Provides the primary flame source for a surface gas burner and directs gas flow for proper combustion
• Restores even heating when an original burner is warped, cracked, or corroded
• Can resolve ignition issues or uneven flames caused by damaged burner ports or misalignment
• Helps prevent gas leakage around the burner when installed correctly and seated flush

• Disconnect gas supply and power to the appliance before servicing
• Confirm burner alignment and seating on the cooktop; replace any damaged grommets or brackets as needed
• Use basic hand tools; avoid modifying the part or cooktop openings

This oven igniter is the glow-bar style part that provides the high heat necessary to light the oven burner so your range reaches and maintains baking and roasting temperatures. Replaces a cracked, weak, or non-heating igniter. What it does:

• Heats to ignition temperature so the gas burner can light reliably
• Fails gradually or suddenly; common symptom is the oven not heating or taking a long time to reach temperature
• A visibly cracked, broken, or glowing-dim igniter typically indicates replacement is needed
• Works with the oven's gas control system to enable proper burner operation

• One igniter assembly

• Disconnect power and gas supply before attempting removal or replacement
• Handle the ceramic/glass igniter element carefully; it is fragile and can break if dropped or flexed
• Inspect electrical connector and mounting hardware for corrosion or damage; replace hardware if not secure

Replace a gas cooktop igniter when burners won't light or click continuously. This spark igniter creates the spark needed to ignite gas burners safely.

Fix a gas cooktop that won't light or clicks continuously with a new igniter. This common wear part typically takes 30-45 minutes to replace.