Bosch Dryer WTB86280 Parts

Temperature monitoring sensor located in the dryer's heating system that regulates drying temperatures. Replace if clothes aren't drying properly, take too long to dry, or if the dryer overheats.

Supports smooth drum rotation in your dryer. Replace if you hear squeaking, whistling, or rumbling during cycles. Verify fit with your model number.

Replacement leveling foot for dryers. Installs on the bottom corner to elevate and stabilize the appliance. Order if cracked, broken, or missing.

The Wheel is an OEM part for Bosch clothes dryers. It is an essential component that works with the drum to tumble clothes, facilitating effective drying action during cycles.

Wheels can cause shorts and come loose over time from heavy drum usage, leading to:

• Vibrating, shaking noises 
• Difficulty spinning the dryer drum by hand
• Stretching or pilling of clothes  
• Unerwven drying performance

Causes of a faulty wheel tend to be wear and tear over time from carrying heavy loads inside a spinning drum. Foreign objects inside the drum can also potentially cause damage.

It is also compatible with some Thermador, Gaggenau, and Kenmore dryer models.

This dishwasher heat exchanger is the side-tank assembly that tempers incoming water and provides a cooled surface for condensation drying. Replacing a cracked or clogged tank restores proper fill, helps drying performance, and stops nuisance leaks. What it does:

• Routes and tempers incoming water before it enters the tub
• Provides a cold surface to condense steam for improved drying
• Assists controlled water flow/level management during fill
• Common symptoms when failed: leaks into the base, leak/error alerts, slow/insufficient fill, and poor drying

• 1 heat exchanger assembly

• Disconnect power and shut off the water supply before service
• Pull the dishwasher out as needed to access the side tank area
• Expect residual water; use towels and a container when removing hoses
• Transfer and securely reinstall existing clamps/seals; verify all connections are seated and leak-free before reinstallation and test run

Dryer drum baffle lifts and tumbles clothes while circulating air evenly. Replace if cracked, loose, or causing noise. Verify fit with your model number.

Fix poor drying or loud noise with this dryer blower fan housing. Restores airflow through the drum and vent system. Moderate DIY repair for many models.

Fix a dryer making loud noises or not tumbling with a new drum. This part holds clothes during the drying cycle and may rust, dent, or crack over time.

Tension roller for dryers. Mounts to the support bracket to maintain proper belt tension around the drum. Replace if worn, squeaking, or damaged.

This is a replacement seal used to restore a watertight connection and help prevent leaks in compatible appliances. It provides a simple, low-cost way to replace a worn or damaged sealing element. What it does:

• Creates a secure, leak-resistant barrier at the mating surfaces where installed
• Helps stop visible leaks and drip symptoms associated with damaged seals
• Restores intended sealing performance when original gasket or seal is deteriorated

• Inspect mating surfaces for damage or debris and clean before installing the new seal
• Make sure the seal seats evenly and is fully inserted into its groove or recess
• Replace only with the correct OEM part number for a proper fit
• Disconnect power and water supply and follow appliance safety procedures before servicing

This replacement seal restores a tight, leak-resistant connection between mating components inside your appliance. Replacing a worn seal helps stop drips at the joint and keeps the system operating reliably without nuisance leak faults.

• Forms a compressible barrier between parts to prevent leakage at a connection point
• Helps protect nearby components from moisture intrusion and corrosion
• Typical failure signs: moisture around a joint, puddling beneath the unit, or leak/overflow error messages
• Replace if the original is cracked, flattened, cut, brittle, or missing

• Disconnect power and shut off the water supply before servicing
• Access the connection, note the seal's orientation, and remove the old seal
• Clean mating surfaces; lightly moisten the new seal and seat it evenly without twisting or pinching
• Reassemble and test for leaks before reinstalling covers or panels

Replacement drum taper cone for your dryer. This structural component secures the drum assembly. Order a new taper if yours is cracked or damaged.

This fill hose routes water from the supply or inlet valve to the appliance tub, restoring normal water flow for cycles that need filling. It's a direct-replacement hose designed to prevent leaks and ensure proper fill performance. What it does:

• Carries incoming water from the inlet valve to the washer/dish tub or dispenser
• Replaces cracked, split or collapsed hose that causes leaks or poor filling
• Helps stop continuous running or under-fill symptoms when the hose is damaged
• Restores a proper water path so fill cycles complete correctly

• One replacement fill hose

• Turn off water supply and power to the appliance before starting work
• Inspect and reuse or replace hose clamps; tighten securely to prevent leaks
• Route hose without kinks and ensure fittings match valve and tub connections

Appliance overheating or won't run? This thermal cutoff opens the circuit at unsafe temperatures to protect your unit. Simple replacement restores safety.