Kenmore Washer 110.20132000 (11020132000, 110 20132000) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3347034
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Wife noticed water on the laundry room floor! Richard L. • Phelps , NY • April 06, 2015
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and...
Read more
More
$49.40
- Compare At:
-
$58.29
- You Save:
-
$8.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP358912
Cap seal creates a tight barrier between cap and mating surface to prevent leaks. Replace when worn or damaged to restore secure fit. Confirm compatibility.
Do-It-Yourself Stories from Customers like You
Washing machine leaking water after cycle Kevin I. • San Diego , CA • February 24, 2020
Read articles and watched How-To video on AppliancePartsPros.com.
Videos were very informational and parts arrived very quickly!
Read more
More
$15.95
- Compare At:
-
$17.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 285353
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Do-It-Yourself Stories from Customers like You
Washer would agitate but would not go into high spin sounded like spin was working though Mario M. • Corona , CA • January 03, 2015
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks.
Door sensor...
Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly.
Timer...
In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10086010
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Do-It-Yourself Stories from Customers like You
Lost a motor fastener in my washer Carl S. • Sweet Home , OR • October 17, 2019
I bought it here. It came quickly. I took the washer apart and put it in.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Washer would fill with water and then do nothing else Richard C. • Torrance , CA • December 05, 2015
I saw videos on it possibly being the lid switch. I used 2 lead wires to bypass the lid switch, which indicated it was indeed the lid switch that was faulty.
I ordered the lid switch, which came in 2 days. I installed it in less than 7 minutes.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP616099
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
- Tightens around a hose and fitting to maintain a secure seal
- Helps stop drips, seepage, or loose connections
- Common fix when you see moisture around a hose joint
- Useful if a clamp is rusted, stretched, or no longer holding tension
What's included: One hose clamp. Install notes:
- Unplug power and shut off water (if applicable) before servicing
- Note clamp position/orientation before removal
- Use appropriate screwdriver or nut driver to tighten evenly
- Do not overtighten—ensure a snug, leak-free seal without damaging the hose
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.95
- Compare At:
-
$11.59
- You Save:
-
$1.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356311
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Do-It-Yourself Stories from Customers like You
Machine was out of balance. Carlton C. • New Milford , CT • April 11, 2021
Problems resolved with suspension spring and screws supplied.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11283272
This is the factory replacement microwave door assembly. It restores a smooth, secure door closure and proper operation so the unit can open and close reliably and look like new. What it does:
- Provides a complete, aligned door to open/close the cavity smoothly
- Ensures latch hooks engage properly so the appliance can operate
- Replaces doors that are cracked, warped, or have broken handle mounts
- Addresses issues like the unit not starting unless the door is pressed, or stopping when the door is moved
- Helps resolve sparking/arcing around the door opening caused by a damaged door choke or screen
What's included:
Install notes:
- Disconnect power at the breaker before servicing; microwaves contain high-voltage components
- For over-the-range units, support or remove the microwave from the wall to safely access and handle the door
- Transfer any reusable hardware/hinge pins/trim from the original door as needed
- Align the hinges and verify the door closes, latches, and opens smoothly before remounting
Do-It-Yourself Stories from Customers like You
Vandalism. Teresa B. • Lewisburg , KY • November 21, 2020
With the parts I purchased from you.
Read more
More
$81.77
- Compare At:
-
$98.12
- You Save:
-
$16.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2172937
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
- Holds three wiring terminals in the correct orientation for a mating connector
- Insulates and locks terminals to reduce arcing and overheating at the plug
- Replaces cracked, brittle, or heat-damaged connector housings
- Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched
What's included:
- 1 three-circuit connector housing
Install notes:
- Disconnect power before servicing the appliance
- Note wire/terminal positions and transfer them one at a time into the new housing
- Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
- Fully seat each terminal until it locks and the connector latch engages securely
More
$13.48
- Compare At:
-
$16.18
- You Save:
-
$2.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 285702
21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.
Do-It-Yourself Stories from Customers like You
Drain hose too short and home depot fix leaked Sara B. • Liberty Hill , TX • August 21, 2015
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly.
Now we're washing again and no leaks!
Read more
More
$34.95
- Compare At:
-
$41.24
- You Save:
-
$6.29