Kenmore Washer 110.21392012 (11021392012, 110 21392012) Parts

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This rubber pad cushions and protects appliance components from vibration and abrasion, reducing noise and wear. It's a small replacement part that restores proper contact and dampening where original pads have worn or fallen off. What it does

• Cushions panels or components to reduce vibration and rattling
• Prevents direct metal-to-metal contact that can cause scratching or wear
• Helps stabilize parts that have shifted due to a missing or damaged pad
• Commonly replaced when noisy operation or visible pad deterioration occurs

• One replacement pad

• Disconnect power before accessing interior panels or components
• Remove any retaining clips or panels that block the pad's location; pad typically presses into place
• Verify orientation and seating against the mating surface; replace any worn fasteners or retainers
• If adhesive was used on the original, use an OEM-recommended adhesive only.

Note: Bearings are only available with the gearcase assembly.

This genuine replacement screw secures components in compatible Whirlpool appliances, restoring proper fit and preventing rattles or loose panels. Use it when original fasteners are missing, stripped, or damaged. What it does:

• Fastens panels, brackets or small components to maintain structural stability
• Replaces missing or worn screws that cause vibration, rattling, or loose parts
• Restores secure connections after repairs or part replacements
• Helps prevent further damage by keeping parts properly aligned

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and hand-start the screw to prevent cross-threading
• Keep small parts away from children and pets during installation

This absorber is the factory-design replacement part that restores the appliance's intended absorption function, helping maintain normal operation and reduce related performance issues. What it does:

• Absorbs and manages moisture/condensate or trapped vapors in the appliance's system to support normal function.
• Helps prevent symptoms commonly linked to a failed absorber, such as excess moisture, unusual odors, or intermittent system cycling.
• Restores the original fit and function when the installed absorber is cracked, broken, or heavily degraded.
• Matches OEM shape and connection points for a direct replacement.

• One absorber replacement as shown

• High-level replacement: access the absorber location; no specialized calibration typically required.
• Disconnect power (and water supply if applicable) before removing panels or replacing parts.
• Handle carefully to avoid damage to surrounding components and wiring; use manufacturer-recommended fasteners.

Color: White. Size: 1 qt. can. Acrylic appliance paint.