Kenmore Washer 110.45996402 (11045996402, 110 45996402) Parts

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This exhaust hose carries drain water from the pump to the external drain connection on your washer. Replacing a worn or damaged hose restores proper draining and helps prevent leaks and musty odors.

• Directs discharge water from the drain pump toward the outlet
• Maintains a sealed flow path to help prevent leaks
• Age, vibration, or debris can cause cracks, splits, or clogs
• Common symptoms: water leaking under the unit, slow or no drain, visible cracks/kinks on the hose

• Disconnect power and turn off water supply before servicing
• Place towels or a pan to catch residual water; remove access panels as needed
• Compress/release spring clamps, transfer them to the new hose, and fully seat hose ends
• Run a short drain cycle to check for leaks

This factory fastener secures appliance components such as panels, brackets, and covers. Replacing a missing, stripped, or rusted screw restores a tight fit and helps reduce vibration, rattling, and shifting during operation.

• Fastens metal or plastic parts to the appliance cabinet/frame
• Helps maintain proper alignment and reduces noise from loose panels
• Replaces hardware that is missing, corroded, or with stripped threads
• Symptoms include rattling, looseness, gaps, or misaligned parts

• Disconnect power; shut off gas/water before servicing
• Support panels to prevent drops; watch for sharp edges
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten; match the original screw's location and orientation

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This dispenser switch is the small electrical switch behind the dispenser lever/paddle. When pressed, it signals the control to dispense, helping restore a responsive lever feel and consistent ice or water dispensing.

• Detects lever/paddle movement and closes the circuit to start dispensing
• Helps fix: no ice or water when the lever is pressed
• Helps fix: must press very hard or hold the lever "just right"
• Helps fix: intermittent operation or a stuck-on dispenser due to a failing switch

• Disconnect power before servicing; turn off water supply if working near water lines
• Access the switch behind the dispenser panel/escutcheon; carefully release trim and tabs as designed for your model
• Note wire positions; move connectors to the new switch in the same locations (NO/NC/COM as applicable)
• Before reassembly, verify a positive "click" and confirm the switch changes continuity when actuated

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This factory fastener secures appliance panels, brackets, and internal components so everything stays aligned and quiet. Replacing a missing or damaged screw restores a tight fit and helps reduce vibration, rattles, and wear.

• Fastens metal or plastic parts to the cabinet/frame
• Maintains alignment of covers, ducts, housings, and brackets
• Replace if the head is stripped, threads are worn, or hardware is missing
• Symptoms can include loose or misaligned panels, rattling/vibration noises, or parts that won't stay secured

• Disconnect power and shut off gas/water before service.
• Match the screw to the original location and reuse existing holes/mounts.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver bit to prevent stripping the head.

This front counterweight mounts to the washer's outer tub to help balance and stabilize the drum during spin. Replacing a damaged weight can reduce vibration and noise and help prevent the machine from walking. What it does:

• Adds mass at the front of the tub to counterbalance loads during spin
• Helps control vibration, shaking, and banging noises
• Can resolve out-of-balance interruptions or excessive movement
• Visible cracks or broken mounting ears indicate the weight needs replacement

• One front counterweight

• Disconnect power and water; use proper lifting techniques—this part is heavy
• Support the tub and remove front cabinet components/door boot as needed for access
• Remove and retain mounting bolts; tighten bolts evenly when reinstalling
• Inspect mounting points and suspension components while accessible; replace if worn

This replacement ball is the small spherical component used in select Whirlpool-built mechanisms. It acts as a moving seal or detent to control flow or position, restoring smooth, reliable operation when the original ball is worn or missing. What it does:

• Provides the sealing or detent action within its valve, hinge, or track assembly
• Helps prevent backflow, leaks, or unwanted movement
• Restores smooth operation when mechanisms feel rough, bind, or won't stay in position
• Replace if the original is deformed, pitted, corroded, or missing

• 1 ball

• Disconnect power and shut off water supply if applicable
• Access the specific assembly per your model's service documentation and note part order
• Place the ball in its seat/track with any companion spring or seal as designed
• Inspect mating surfaces and related seals or springs and replace if worn

This L-shaped flowmeter hose is part of the washer's water inlet circuit. It routes water through the flow sensor and maintains a tight, leak-free connection, helping the machine fill accurately and operate as designed.

• Channels incoming water through the flowmeter for correct fill measurement
• Maintains a secure, leak-resistant connection within the fill system
• Typical failure signs: water dripping during fill, visible cracking/hardening, loose fit, or kinks restricting flow
• A damaged or leaking hose can contribute to inaccurate fill sensing or fill-related errors

• Disconnect power and shut off both water supplies before servicing
• Note routing/orientation; transfer existing clamps or install new ones if needed
• Fully seat hose on each fitting and secure clamps without over-tightening
• Restore water and power, then run a fill to check all connections for leaks

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

This Marquardt ground switch completes the appliance's ground connection so controls and safety systems have a proper reference. Replace a failed ground switch to restore reliable grounding and help eliminate related electrical faults. What it does:

• Provides the ground connection path used by controls and safety circuits.
• Replaced when continuity tests fail or when appliances have intermittent power, control errors, or nuisance breaker trips.
• Restores correct electrical grounding to help reduce fault conditions and erratic control behavior.
• Matches the original switch form and electrical connector layout for a direct replacement.

• Disconnect all power (unplug appliance and/or shut off breaker) before beginning service.
• Photograph or label wiring and connector positions before removal; transfer connectors to the new switch exactly.
• Inspect connectors and wiring for damage; replace any frayed or heat-damaged wiring.

This part is a replacement outer tub. This part's intended use is to repair a broken or defective outer tub in washing machines.The outer tub fits over the spin basket and is what ensures that the machine doesn't leak during use by sealing in the water. If this part is broken, water may drip or leak, and thus the front tub should be immediately replaced. It's important that the appliance is unplugged before any attempt is made to replace this part. Work gloves are recommended for proper safety and protection.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This is an authentic OEM replacement part made of high-quality materials. This outer tub can be used with different models of washing machines that have been manufactured by Whirlpool, KitchenAid, Kenmore, Scotsman, and some other brands. It is sold individually.

This retaining nut secures components within the pump/motor assembly, keeping them tight and properly aligned so your appliance can circulate water reliably. A worn or missing nut can lead to leaks, noise, or poor wash performance.

• Holds pump/motor parts firmly in place to prevent loosening and leaks
• Helps maintain proper water circulation and wash quality
• Direct-fit replacement for the original fastener in applicable units

• Disconnect power and shut off water before servicing
• Access the pump/motor area; note orientation of parts before removal
• Hand-start threads carefully to avoid cross-threading, then tighten to secure
• Inspect related seals and O-rings; replace any damaged components during reassembly