Kenmore Washer 110.47081601 (11047081601, 110 47081601) Parts

Secure dryer vent hose to exhaust outlet and wall connection. Replace worn clamps to prevent duct slippage and maintain proper airflow. Confirm fit.

Securely mounts your dryer above your washer to save floor space. Includes brackets, adhesive pads, and hardware for safe installation. Replaces lost kits.

This exhaust hose carries drain water from the pump to the external drain connection on your washer. Replacing a worn or damaged hose restores proper draining and helps prevent leaks and musty odors.

• Directs discharge water from the drain pump toward the outlet
• Maintains a sealed flow path to help prevent leaks
• Age, vibration, or debris can cause cracks, splits, or clogs
• Common symptoms: water leaking under the unit, slow or no drain, visible cracks/kinks on the hose

• Disconnect power and turn off water supply before servicing
• Place towels or a pan to catch residual water; remove access panels as needed
• Compress/release spring clamps, transfer them to the new hose, and fully seat hose ends
• Run a short drain cycle to check for leaks

Factory mounting screw secures panels, brackets, hinges, and covers on your washer. Replace missing, stripped, or rusted screws to restore secure fit.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

Fix detergent not dispensing or musty odors with a new dispenser divider. This small part routes powder or liquid detergent properly. Easy DIY fix.

Secures hoses to fittings to prevent leaks and blow-offs. Replace if rusted, stripped, or loose to restore a tight seal. Verify fit with your model.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Front counterweight that mounts to the washer's outer tub. Replace if cracked, broken, or missing to restore proper balance and reduce vibration during spin.

Fixes F02 drain error codes and slow draining. This small ball creates a seal in the tub-to-pump hose to control water flow. Simple DIY replacement.

This dishwasher door latch lever links the handle to the latch and safety switches so the door can secure closed and the cycle can start. Replacing a cracked or worn lever restores reliable latching and starts. What it does:

• Transfers handle movement to the latch mechanism and door switches
• Helps the control recognize a fully closed door so the dishwasher will run
• Contributes to keeping the door securely closed during operation
• Resolves: cycle won't start, door won't latch or stay closed, need to hold door to run, loose/floppy handle feel

• 1 lever

• Disconnect power at the breaker before servicing the door
• Open the door and remove inner door panel screws to access the latch/handle area
• Note the original lever's orientation; move any springs/clips to the new lever and seat it fully in the pivot
• Reassemble, verify smooth handle action, and ensure the door latches and a cycle initiates

Washer won't start or shows electrical faults? A failed ground switch disrupts the safety circuit. This switch restores proper grounding for reliable operation.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

Includes water temperature sensor.

This drawer hook is the retainer that keeps an appliance drawer securely seated while still allowing easy release for cleaning or service. Replacing a worn or broken hook restores smooth, reliable drawer operation.

• Secures the drawer in its housing so it stays closed during use
• Acts as the catch/release point for removing the drawer when needed
• Helps maintain proper alignment for smooth opening and closing
• Common symptoms: drawer won't stay closed, pops open or falls out, won't latch, or the hook is visibly cracked/missing

• Disconnect power before servicing
• Fully open and remove the drawer to access the hook area
• Align the new hook with the slots/tabs and snap or seat it into place
• Avoid forcing components; refer to the service manual for model-specific steps