Kenmore Dryer 110.69832801 (11069832801, 110 69832801) Parts

Replaces a cracked, broken, or missing dryer drum baffle. Installs inside the drum to lift and tumble clothes during the drying cycle. Easy repair.

Replacement retainer clip that secures panels and internal components in your dryer. Install when the original clip is broken, worn, or missing.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

The Door Seal is an OEM component specifically designed for Whirlpool dryers. It works to create an airtight seal between the dryer door opening and drum interior. During operation, heated air and moisture are contained within the drum thanks to this crucial seal. 

Symptoms of a worn door seal include:

• Increased drying time due to air leaks
• Clothes not drying completely before end of cycle  
• Excess humidity escaping into home
• Discoloration or residue buildup on door glass

Causes of failure are normal wear and compression over extended use, or damage from improper door closure. A worn seal degrades efficiency and performance of the dryer.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Replace a worn or damaged dryer drum that's causing noise, poor tumbling, or clothing snags. Sheet metal construction holds laundry during cycles.

Mounting screw for dryer installation and panel assembly. Replace this hardware if the original is stripped, missing, or damaged during disassembly.

Replace a damaged, frayed, or broken wire harness in your dryer. This internal wiring component connects electrical parts. Order today if yours is worn.

Cabinet housing for dryers. This outer shell encases internal components. Replace if cracked, rusted, dented, or structurally damaged from impact or wear.

Holds the dryer bulb and provides electrical connection for interior lighting. Replace if cracked, heat-damaged, or causing flickering lights. Confirm fit.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Jumper wire for dryer broken belt switch. Installs on idler arm assembly. Replace if wire is damaged, broken, or missing after belt replacement.

This is a replacement 8-18 x 7/32 machine screw used to secure panels and small components in compatible Whirlpool appliances. It restores proper fastening where a screw is missing, stripped, or damaged. What it does:

• Secures panels, trim pieces, brackets or small components to prevent movement
• Helps stop rattling, vibration noise, or loose-fitting parts
• Replaces missing or damaged screws to restore proper alignment of panels or controls
• Used wherever an 8-18 x 7/32 machine screw is specified by the manufacturer

• Unplug the appliance or turn off power before servicing.
• Use the correct screwdriver or bit to avoid stripping the head; tighten snugly but do not over-torque.
• Replace any stripped inserts or mating hardware if threads are damaged.

Fix a dryer that won't stop running when the cycle ends. This end of cycle switch signals the timer to stop. Simple DIY repair for most models.

Secures the light bulb socket inside your dryer drum. Replace if the bracket is cracked, broken, or missing to properly mount the drum lighting assembly.