Kenmore Washer 110.72408130 (11072408130, 110 72408130) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
This wire retaining ring secures the door boot (bellow) to the front tub on front-load washers. It keeps the gasket seated to maintain a watertight seal, helping prevent leaks when the washer fills, agitates, and spins.
- Secures the door boot/gasket to the outer tub opening
- Maintains a watertight seal during wash and spin cycles
- Helps prevent the boot from slipping off the tub lip
- Common symptoms: water leaking at the front, a loose or detached boot, or a broken/missing ring
Includes: 1 wire retaining ring Install notes:
- Unplug the washer and shut off water; wear gloves and eye protection—the ring is under spring tension
- Release the outer boot clamp and fold the boot inward to access the inner ring
- Seat the boot evenly on the tub rim, then expand and fit the ring into its groove; verify it's fully seated all the way around
- Reassemble and run a quick test cycle to check for leaks
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP367594
This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.
- Provides front support and height adjustment to level the unit
- Helps reduce rocking, vibration, and rattling during operation
- Replaces a worn, broken, missing, or stripped front foot
- Helps ensure doors or drawers align and close properly when leveled
What's included: 1 front foot assembly Install notes:
- Disconnect power and, if applicable, shut off water/gas before servicing
- Protect flooring; carefully tip or brace the appliance to access the front foot
- Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
- Verify stability, then restore utilities and recheck for level
Do-It-Yourself Stories from Customers like You
Front foot was damaged Deborah L. • Mount Pleasant , WI • June 08, 2015
Replaced, it was a cinch!!!
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$19.79
- Compare At:
-
$21.36
- You Save:
-
$1.57
Genuine Whirlpool part
By: Whirlpool
Part Number: 350365
2 Port. Whirlpool and Kenmore washers.
Do-It-Yourself Stories from Customers like You
Water drain pump would not turn any more Robert T. • Belleville , IL • January 20, 2016
Ordered a replacement. Had to tip washer toward the back to provide access underneath to the
pump. Had some difficulty removing the two hose clamps. Pliers were not the best tool. Had to ensure the drive belt was properly engaged with the pulley of the pump.
Read more
More
$92.56
- Compare At:
-
$110.15
- You Save:
-
$17.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP359231
This protective cover for the washer's lid switch area guards the switch and wiring from water, detergent, and snagging inside the top panel, supporting reliable lid-closed detection and long-term safety interlock performance.
- Shields the lid switch and wiring from splashes, detergent, and debris under the top panel
- Helps prevent snagging or accidental contact with the switch mechanism
- Supports consistent lid-closed sensing by keeping the switch area protected and in position
- If the shield is damaged or missing, you may notice exposed switch/wiring or intermittent starting/spinning that improves when the lid is pressed
What's included: 1 shield Install notes:
- Disconnect power before servicing; turn off water if moving the appliance
- Access the lid switch area by raising the top or opening the console per the service procedure
- Install the shield in the original orientation and secure with the existing fasteners
- After reassembly, verify the lid closes properly and the washer starts/spins as expected
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596797
Genuine Whirlpool part
By: Whirlpool
Part Number: WP94614
For mating terminal use [AP31136300].
More
$4.95
- Compare At:
-
$5.89
- You Save:
-
$0.94
Genuine Whirlpool part
By: Whirlpool
Part Number: 285205
A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:
- Supports axial load on the transmission/gearcase shaft to reduce friction and wear
- Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
- Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
- Helps maintain proper alignment of transmission components for smoother operation
What's included: One thrust bearing Install notes:
- Disconnect power and water supply and drain the washer before beginning any work.
- Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
- Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Made by Whirlpool. Fits most Whirlpool, Kenmore, Estate and Roper belt driven washing machines.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine would not stop dripping into basket when finished washing Howard S. • Minneapolis , MN • April 25, 2021
Replaced washer water inlet valve.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21365
This small hardware washer is used as a spacer and load distributor within the specified assembly. It helps maintain alignment and smooth operation by reducing friction and restoring a secure fit when the original washer is worn or missing. What it does:
- Distributes load under a screw or bolt to keep joints secure
- Maintains proper spacing and alignment between mating parts
- Reduces friction and wear at the contact surface
- Replace if missing, bent, cracked, or excessively worn; clues include wobbly parts or scraping/squeaking noises
What's included:
Install notes:
- Disconnect power and shut off water supply before servicing
- Refer to your model's parts diagram for exact location and stack order
- Clean mating surfaces; replace any damaged fasteners or bushings
- Tighten hardware evenly and do not overtighten
Do-It-Yourself Stories from Customers like You
Washing machine would not agitate or spin. Laurie W. • Webster , NH • March 25, 2017
We were a bit doubtful that we could find parts for this Whirlpool washing machine as it is 22 years old. We were SO pleased that not only could we find them ( with excellent customer service) but they were shipped in an appropriate time. My handy husband was then able to repair it himself :)
Read more
More
$7.40
- Compare At:
-
$8.88
- You Save:
-
$1.48
Genuine Whirlpool part
By: Whirlpool
Part Number: 350938
Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Dryer drum completely wore off all coating Larry W. • Ubly , MI • July 01, 2016
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92