Kenmore Freezer 253.29401992 (25329401992, 253 29401992) Parts

A small metal clamp that secures the refrigerator's capillary (temperature sensing) tube to the cold control so the thermostat reads temperatures accurately. Replaces worn or missing clamps to keep the sensing tube stable and prevent movement-related issues. What it does:

• Holds the capillary/sensing tube firmly against the cold control or cabinet
• Helps maintain accurate thermostat sensing by preventing tube movement
• Reduces vibration or rattling from a loose sensing tube
• Stops intermittent temperature swings caused by a displaced capillary tube

• Disconnect power before servicing the appliance.
• Handle the capillary tube gently; avoid kinks or sharp bends.
• Install clamp over the tube and secure to the control or bracket using the factory hole or fastener; do not overtighten.

This electrical relay assembly controls power to a major appliance circuit, restoring reliable switching and helping appliances start and run properly. Replace a failed relay to stop intermittent starts, no-start conditions, or unreliable operation. What it does

• Switches electrical power to motors or heating circuits when the appliance control signals for operation
• Commonly fails after arcing or overheating, causing intermittent or no-start symptoms
• May cause a unit to click repeatedly, run intermittently, or fail to power specific functions
• Restores correct electrical switching when installed in place of a damaged relay

• Disconnect power before accessing control panels or wiring to avoid shock
• Access and removal typically require removing the control panel or top panel; keep track of screws and wire locations
• Replace with the exact part number and reconnect all terminals securely; do not bend or damage connector pins

This drain tube insulation cushions and thermally protects the refrigerator's defrost drain tube to help prevent condensation and ice buildup. It keeps the drain line insulated so water flows freely to the drip pan and reduces drip/ice-related issues. What it does:

• Wraps around the defrost drain tube to limit heat transfer and condensation.
• Helps prevent drain freeze-ups that can cause water pooling or slow drainage.
• Reduces the chance of water dripping inside the cabinet or onto the floor.
• Supports reliable defrost water routing to the drain pan.

• Always unplug the appliance or disconnect power before servicing.
• Access may require removing the back or inside panel; keep track of fasteners.
• Slide the insulation over the drain tube so it fully covers the exposed section; ensure it sits flat without kinks.
• If corrosion or heavy buildup is present, clean the drain tube before installing new insulation.

This Hose-Drain is the appliance drain line that carries waste water away from the unit to the household drain, helping restore proper draining and prevent water buildup. Replace a cracked or clogged hose to stop leaking and poor drain performance. What it does:

• Channels wastewater from the appliance to the household drain or disposal
• Restores normal draining when a worn or damaged hose causes pooling or slow drain
• Helps prevent leaks and water damage caused by cracks, splits, or loose connections
• Works with the appliance's existing clamps and fittings to maintain a sealed drain path

• One Hose-Drain

• Disconnect power and water supply before servicing; follow appliance safety guidelines
• Inspect and reuse or replace clamps/fittings as needed for a secure seal
• Route the hose to match the original path, avoiding kinks or tight bends
• After installation, run a short cycle and check all connections for leaks

This retainer lead wire secures appliance wiring to keep harnesses organized and away from heat or moving parts, reducing wear and accidental disconnection. It's a simple replacement to restore proper wire routing and protection. What it does:

• Clips or holds the wiring harness in place to prevent chafing and strain
• Helps keep wires away from hot surfaces, vents, or moving components
• Reduces risk of intermittent electrical connections caused by loose wiring
• Restores factory routing after service or component replacement

• Disconnect power to the appliance before installing to avoid shock or injury
• Remove any panels necessary to access the original retainer and wiring route
• Replace like-for-like, seating the retainer securely so the harness cannot shift
• If wires show damage or insulation wear, inspect further and replace damaged wiring before reassembly

This breaker kit is a factory-style replacement kit that restores the cabinet bracket and corner supports so the appliance components stay properly aligned and secure. It helps fix loose or damaged mounting where breaks or worn corners allow movement. What it does

• Replaces the breaker bracket assembly and corner pieces that secure cabinet components.
• Restores alignment and prevents shifting or sagging caused by broken or worn parts.
• Common symptom: noisy or loose cabinet sections, misaligned panels, or parts that move when the appliance is bumped.
• Designed to match OEM fit and function for a direct replacement.

• High-level replacement: remove access panels and old bracket/corners, then install the kit using original fasteners or supplied hardware.
• Use basic hand tools; keep track of removed screws and clips for reassembly.
• Disconnect power and follow appliance safety procedures before starting work.