Kenmore Dryer 417.81100000 (41781100000, 417 81100000) Parts

This door gasket is the flexible sealing strip that helps keep cold air inside your refrigerator, improving temperature stability and efficiency. It replaces worn or torn seals to reduce drafts and moisture intrusion. What it does:

• Creates an airtight seal around the refrigerator door to help maintain proper internal temperature
• Helps prevent frost buildup and condensation by keeping warm, humid air out
• Reduces energy waste caused by cool-air leaks around the door
• Can fix common symptoms like warm spots near the door, excessive frost, or an overworking compressor

• High-level replacement: usually removed from the door channel and pressed into place; may require loosening door hinges for full removal on some models
• Check that the gasket sits evenly in the channel and that the door closes flush to ensure a proper seal
• Clean the door channel and mating surface before installing to ensure good adhesion and sealing

This electrical wire harness connects key components to deliver power and signal paths so your appliance controls and features operate reliably. It replaces a damaged or worn harness to restore proper electrical connectivity. What it does:

• Routes power and signal between control board, sensors, and accessories
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps resolve symptoms like lights, fans, or controls not powering on or working erratically
• Maintains proper connector fit and wiring color-coding for correct hookups

• One electrical wire harness

• Disconnect power before inspecting or replacing the harness to avoid shock
• Confirm connector orientation and secure all clips; route wiring away from heat and moving parts
• Inspect mating connectors for damage and replace if corroded or burned

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This replacement cushion is a small rubber bumper that protects components and reduces vibration and noise where panels, doors, or assemblies meet. It helps keep parts aligned and prevents metal-on-metal contact. What it does:

• Absorbs shock and reduces vibration to minimize rattling or movement
• Protects surfaces from wear and prevents scraping or chafing
• Helps maintain proper spacing or alignment of panels or assemblies
• Works wherever a soft bumper or spacer is required

• Disconnect power to the appliance before servicing.
• Remove any covers or panels to access the mounting area.
• Press or seat the cushion into the locator/receptacle; replace retainers if present.

One per package.

The Steam Hose Kit is an OEM part for Frigidaire dryers. It provides the necessary conduit for steam from the water source to the dryer. The kit includes: 
5’ Rubber Fill Hose with Gooseneck
1’ Rubber Fill Hose (Female/Female)
All Male Y Connector

Causes of a bad steam hose can range from normal wear and tear to improper installation or physical damage from external sources.  

Symptoms of a bad Steam Hose Kit include:

• Leaks or drips from the hose connections.
• Reduced steam output, affecting the dryer's ability to effectively remove wrinkles or sanitize clothes.
• Noticeable wear or damage to the hose, such as cracks or splits.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Hex washer head ,10-32 x 0.375. Ground

This is a mounting bracket that secures and supports appliance components, helping keep panels and assemblies aligned for stable operation. It's a simple replacement part that restores proper fit and reduces movement or rattling. What it does:

• Secures and supports a panel or internal assembly to the appliance frame
• Keeps components aligned to prevent binding or misalignment
• Reduces vibration and rattling caused by loose fittings
• Restores proper mechanical support after breakage or wear

• Disconnect power and/or water to the appliance before beginning any repair
• Use appropriate hand tools; keep track of fasteners and any shims or clips
• Beware of sharp sheet-metal edges; wear gloves and eye protection

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

This rubber grommet cushions and secures wiring, tubes, or panels to prevent chafing and reduce vibration. It helps keep components aligned and quiet for reliable appliance operation. What it does:

• Cushions parts where metal meets metal to prevent wear and chafing
• Dampens vibration and reduces rattling or squeaking noises
• Holds wiring or tubing in place to maintain proper routing
• Helps protect against abrasion and occasional minor movement

• Disconnect power and leave appliance unplugged before starting any repair
• Remove the damaged grommet and clean surrounding area before installing the new piece
• Press or stretch the grommet into place; use gentle tools (plastic trim tool) to avoid damage
• Inspect adjacent wiring/tubing for damage and replace if frayed or pinched

This replacement air baffle vane directs cooled air inside the refrigerator to help maintain even temperature distribution and proper airflow between compartments. Replaces a cracked or missing vane to restore intended airflow control. What it does:

• Directs and channels cold air from the evaporator to the refrigerator/freezer compartments
• Helps reduce uneven cooling and temperature stratification
• Prevents excessive airflow in one area that can cause frost buildup or warm spots
• Replaces broken, cracked, or warped vanes that rattle or obstruct airflow

• Disconnect power before beginning any repair to avoid electrical hazard
• Access typically requires removing shelves or the evaporator cover; keep parts organized
• Handle gently to avoid cracking the replacement vane during installation
• Use basic hand tools;