Kenmore Washer Dryer Combo 417.98802890 (41798802890, 417 98802890) Parts

This mechanical cycle timer controls the sequence and duration of wash, rinse and spin functions in compatible top-load washing machines, restoring proper cycle advancement and timing. What it does:

• Advances the washer through timed cycles so selected wash, rinse and spin functions run in the correct order.
• Routes power to the washer's motor and valves at the right points in the cycle.
• Commonly replaces timers that cause machines to get stuck on one cycle, fail to advance, or not complete a cycle.
• Works with the machine's existing control knobs and wiring harness to restore automatic cycle sequencing.

• Disconnect power to the washer before beginning any service to avoid electrical shock.
• Service typically requires access behind the console or control panel; remove panels carefully and keep fasteners organized.
• Note and photograph wiring connections before removal; reconnect wires to the same terminals.

For seal only use part number 131901400.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

This push-in fastener secures plastic trim and interior panels to the appliance chassis, restoring a snug fit and reducing rattles or gaps. Simple, durable replacement for worn or missing retainers. What it does:

• Secures trim pieces, door panels, or interior components to the cabinet
• Keeps panels aligned to prevent vibrations and rattling noises
• Replaces missing or broken retainers that allow gaps or loose trim
• Works where a snap-in or push-retainer style fastener is specified

• Disconnect power to the appliance before servicing to avoid electrical risk.
• Remove surrounding trim or panels as needed to access the mounting hole.
• Push the fastener into the panel hole until it snaps or seats fully; ensure a flush fit.
• Replace with an identical fastener if size or stem design differs.

Hex washer head. 5/16-18 x 0.625

This replacement control panel restores the appliance's front console appearance and provides the mounting surface for the user controls. It lets you replace a cracked, faded, or damaged console so controls sit and function correctly. What it does:

• Replaces a damaged or cracked front console panel and restores a finished appearance
• Provides the mounting surface and protection for switches, touchpads, and display components
• Helps stop drafts or light leaks from a broken panel that affect user access
• Common symptoms: visible cracks, broken mounting tabs, loose or rattling console, or exposed control openings

• Disconnect power before beginning any repairs to avoid shock; if applicable, unplug the appliance or switch off the breaker
• Handle panels carefully to avoid cutting on sharp edges or damaging attached trim pieces
• Some installations require removing trim pieces, fasteners, or the control assembly; keep hardware organized for reassembly

A coiled roll pin used to secure shafts, rollers, or linked components in place, helping maintain proper alignment and smooth operation. Ideal when a worn or damaged pin allows movement or causes noisy parts. What it does:

• Secures shafts, rollers, or pivots by fitting into a mating hole to prevent axial movement
• Keeps rollers and linked components aligned for smooth rotation and operation
• Common symptom: loose or wobbling roller/shaft or parts that shift during use
• Common symptom: unusual noise or intermittent binding where a pin retains a component

• Disconnect power to the appliance before beginning any work
• Removal/installation may require a punch and hammer or pliers; protect surrounding surfaces
• Replace with the exact part number to ensure correct fit and retention
• Keep small parts away from children and pets