Kenmore Range 790.31063100 (79031063100, 790 31063100) Parts

Specs: 8 x 0.750

This is a replacement glass door assembly made by Frigidaire. It is made of tempered glass and allows the user to see into the oven and observe food as it cooks. It also prevents heat from escaping.Glass oven doors can be damaged by contact with cold liquids that cause the glass to contract rapidly. If the glass is cracked or broken, the door will need to be replaced. To replace the oven door, locate the screws under the door lip. Remove the bolts holding the handle to the front, and the door should lift away. Reverse these steps to install the new door. The door is quite heavy and may require two people to safely uninstall/install.This is an OEM part. It is sold individually and is compatible with Kenmore and Frigidaire ovens.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This oven lower bake element is the heating element that warms the oven cavity for baking and roasting. It restores proper baking heat so food cooks evenly and reaches set temperatures. What it does:

• Generates heat for the oven's bake function to cook and brown food
• Commonly causes no-heat or weak-heat oven symptoms when failed
• Can cause uneven baking or longer preheat times if damaged
• May show visible breaks, burn spots, or arcing when defective

• Disconnect electrical power to the appliance before starting any work
• Handle carefully and avoid bending the element; use gloves to protect hands
• Verify proper wire connections and secure mounting during reassembly

This wiring harness routes power and control signals between refrigerator components to restore proper electrical connections and operation. It replaces a damaged or disconnected harness to help resolve intermittent power, control, or component failures. What it does:

• Carries voltage and control signals between the control board, compressor, fans, lights, and other components
• Restores lost connections that can cause intermittent operation, no power to circuits, or non-working fans/dispensers
• Replaces brittle, frayed, or corroded wiring and broken connector ends that cause faults or error codes
• Helps prevent shorts and erratic behavior when damaged wiring is the root cause

• One wiring harness

• Always disconnect power to the appliance before beginning service
• Verify connector orientation and fully seat each plug; do not force mismatched connectors
• Route harness to avoid heat sources, sharp edges, and pinch points; secure with original clips or ties

This front console control panel replaces a worn or damaged oven/range control surface and restores access to your unit's buttons and display for normal operation. It provides the visible interface where settings are selected and displayed. What it does:

• Replaces the exterior control surface used to select cook modes, temperatures, and timers
• Restores tactile button access and the area around the display when the original panel is cracked, faded, or broken
• Commonly used when buttons stick, the panel is cosmetically damaged, or the control surface no longer secures properly
• Does not include electronic control boards or internal components unless specified

• High-level task: remove screws and trim pieces, disconnect any ribbon cables or harnesses, and secure the new panel in place
• Disconnect power at the breaker before servicing to avoid electrical shock
• Handle ribbon cables and connectors gently; do not bend pins or force connectors

This control panel provides the user interface for your appliance, restoring a clean, functional console so buttons and displays operate correctly. It matches the original style and mounts in the appliance's front console area. What it does:

• Replaces a damaged, cracked, or faded front console panel to restore normal control access
• Secures and supports the appliance's buttons, touchpads, and display area
• Helps stop dirt and moisture from reaching internal electronics behind the console
• Common symptom fix: visible damage, non-sealing panel edges, or loose/missing console trim

• One control panel

• Disconnect power before starting any repair to avoid shock or damage
• Requires basic hand tools; remove screws and retaining clips to swap panels
• Handle carefully to avoid scratching the finish or damaging attached brackets
• If the original overlay or electronic components are attached, transfer them exactly as removed

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing