Kenmore Range 790.41032801 (79041032801, 790 41032801) Parts

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This decorative trim piece restores the finished appearance on the appliance door or control area and covers the mounting edges for a clean, factory look. Replaces a scratched, dented, or missing trim to improve appearance. What it does:

• Covers and protects the edge of the door or control opening to keep a finished appearance
• Hides fasteners and gaps for a smoother exterior surface
• Prevents dirt and moisture from collecting in the trim gap
• Restores original aesthetics after damage or during panel replacement

• One decorative trim piece

• Install with basic hand tools; align trim over mounting area before fastening
• Do not force or bend trim; inspect adjacent mounting tabs for damage
• Disconnect power to the appliance if installation requires removing electrical panels or access behind the trim
• Replace with OEM-specified fasteners for a secure fit

This top burner orifice meters gas to a 14,000-BTU surface burner on your range, maintaining the correct flame size and heat output. Replace a worn or incorrect orifice to restore consistent burner performance and control. What it does

• Regulates gas flow to the 14,000-BTU top burner for proper flame height and shape
• Helps resolve weak or oversized flames and uneven heating
• Can reduce yellow/orange flame tipping and improve simmer control
• Supports reliable ignition by ensuring correct fuel metering

• One 14,000-BTU top burner orifice

• Shut off gas supply and power; allow the cooktop/range to cool before service
• Remove burner cap and head to access the orifice; use the correct socket/wrench
• Install and snug—do not overtighten; verify it's the correct orifice for the burner position and gas type specified for your model
• Reassemble, check for leaks with a soapy-water solution, and verify a stable, blue flame (adjust air shutter if applicable)

This glide is the low-friction slide piece used in select Frigidaire ranges and wall ovens to support a moving component. Replacing a worn glide restores smooth in-and-out movement, reduces binding, and helps prevent premature wear on mating rails. What it does:

• Provides a smooth, low-friction surface for a sliding drawer or rack
• Helps keep the component aligned on its track to avoid binding
• Reduces sticking and scraping noises during operation
• Common symptoms: hard-to-open/close movement, uneven travel, wobbling, or a visibly cracked/missing glide

• One glide

• Disconnect power and allow the appliance to cool before servicing
• Remove the drawer or rack to access the glide location
• Release screws or tabs securing the old glide; transfer any reusable hardware
• Install the new glide, and test for smooth travel

This handle mounting screw is an authentic OEM replacement part sourced directly from the manufacturer for use with oven handles. The oven handle attaches to the oven door with two of these screws. If the washer that goes with the screw is loose or missing, the screw will become loose, and the handle may break away from the door. If this occurs, the door will be difficult to open when not in use and nearly impossible to open when hot. If the mounting screw is loose or missing, the screw should be replaced immediately. Note that the washer needed for the screw is not included and should be purchased separately.Make sure the oven is not hot before replacing the door handle mounting screw. To start, disconnect the power from the oven. Remove the screw and washer from the handle if it is loose and install a new handle mounting screw with a new washer. Tighten the screw until it is flush with the door. Repeat for the remaining screw if necessary.This handle mounting screw is a heavy-duty black metal screw that is sold individually. It is designed for use on ovens manufactured by Frigidaire.