Kenmore Range 790.78309010 (79078309010, 790 78309010) Parts

This wire rack provides a sturdy, corrosion-resistant shelf surface to support food containers, pans and other items inside the compartment. It restores usable storage space and helps keep items organized and level. What it does

• Replaces a bent, broken or missing wire shelf so items sit flat and don't slide or tip
• Supports dishes, trays and food containers for safe storage and even airflow
• Maintains proper spacing for drawers and other interior components to operate
• Visible wear or rust on the wires can cause sharp edges or instability

• High-level swap: remove any items, lift out the old rack and set the new rack into the existing support grooves or clips
• No special tools typically required; gentle pressure may be needed to seat rack into supports
• If rack has mounting clips, confirm clips are intact and positioned correctly before use
• For safety, avoid forcing parts;

This insulation panel fits inside the refrigerator cabinet to help maintain interior temperatures and reduce heat transfer to the outer shell, supporting more consistent cooling and helping limit frost buildup. What it does:

• Forms a thermal barrier between the interior liner and outer cabinet to help hold cold air inside.
• Helps reduce frost and moisture buildup around the liner when intact.
• Worn, torn, or missing insulation can contribute to longer run times, uneven cooling, or more frequent defrost cycles.
• Replaces damaged insulation to restore proper temperature retention and improve appliance efficiency.

• Always disconnect power to the appliance before starting any repair.
• Panel may be secured with clips, adhesive, or foam sealant; remove and install carefully to avoid damaging the liner.
• Inspect surrounding seals, gaskets, and fasteners while accessing the cavity; replace any damaged components.

Note: ONE screw only, order as needed.

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

This door trim kit replaces worn or damaged decorative trim to restore the finished look of your appliance door and cover exposed edges. It's a simple cosmetic service part that improves appearance and helps protect the door edge. What it does:

• Replaces cracked, chipped or missing door trim for a neater appearance
• Covers exposed edges and hides minor cosmetic damage
• Restores original finished profile around the door perimeter
• Helps prevent dirt and moisture from collecting in exposed gaps

• One door trim kit

• Disconnect power to the appliance before beginning any work
• Use basic hand tools; follow for disassembly/reassembly steps
• Work carefully around trim edges to avoid scratching the door finish
• If trim attaches with clips or screws, save fasteners and replace in the same positions