Kenmore Range 790.92802011 (79092802011, 790 92802011) Parts

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This flat replacement glass shelf provides a stable, easy-to-clean surface inside the refrigerator to help organize and protect food. It restores proper shelving where the original glass was cracked, scratched, or missing. What it does:

• Replaces a flat refrigerator shelf glass to support food items and containers
• Restores even storage surfaces and prevents spills from soaking shelves below
• Helps maintain refrigerator interior organization and visibility of contents
• Fits into existing shelf supports or trim rails when the original glass is damaged or removed

• One flat replacement glass shelf

• Handle the glass carefully and wear cut-resistant gloves to avoid injury
• Remove food and any trim/shelf supports before swapping the glass
• Place the new glass into the existing rails or supports; do not force or bend components
• If any clips, rails or seals are damaged, replace them before use to ensure proper fit and safety

This replacement control switch restores a single appliance control function by completing or interrupting the circuit that powers that feature. Fits select Frigidaire appliances to replace a failed or intermittent control switch. What it does:

• Acts as the user/control interface switch that opens or closes power to a specific circuit
• Replaces a worn or failed switch that causes a feature to not respond or work intermittently
• Helps stop unwanted operation when a switch sticks or shorts
• Restores reliable on/off or stepped control for the affected function

• Always disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions before disconnecting
• Require removal of a control panel or access panel; keep screws and small parts organized

This cabinet insulation panel helps reduce heat transfer and noise so your refrigerator reaches and keeps proper cooling more efficiently. It's a simple replacement that restores thermal barrier performance inside the cabinet. What it does:

• Replaces worn or damaged insulation to help maintain consistent internal temperatures
• Reduces compressor runtime and thermal cycling caused by heat gain
• Minimizes drafts, cold spots, and excess frost buildup around the cabinet
• Dampens vibration and operating noise for quieter performance

What's included:

• One cabinet insulation panel

Install notes:

• Disconnect power to the appliance before servicing to avoid shock hazards
• Access may require removing interior liners or trim; keep fasteners for reassembly
• Fit the panel into the cabinet cavity in the original orientation; secure as originally installed
• Inspect surrounding seals and components while the cabinet is open; replace any damaged parts

This insulator is a molded protective cushion that reduces vibration and protects nearby components from wear or contact. It helps keep parts stable and minimizes noise for smoother appliance operation. What it does:

• Cushions components to reduce vibration and rattling
• Protects wiring, tubing, and panels from abrasion and impact
• Helps maintain proper spacing between parts to prevent rubbing
• Can reduce operational noise caused by loose or contacting parts

• One insulator

• Disconnect power to the appliance before starting any repair
• Remove the access panel(s) needed to reach the mounting area; retain fasteners
• Press or slide the insulator into the correct position; it fits snugly and secures the component
• If removal requires cutting old adhesive or clips, replace with equivalent fasteners or adhesives approved by the manufacturer