Kenmore Range 790.92809012 (79092809012, 790 92809012) Parts

This interior refrigerator liner replaces a damaged or worn cabinet surface to restore a clean, smooth interior and support shelves and drawers. It helps maintain a sanitary storage area and a proper fit for accessories. What it does:

• Provides a smooth, easy-to-clean interior surface for the fresh food compartment
• Restores mounting surfaces for shelves, bins and trim pieces
• Prevents drafts and moisture intrusion where cracks or gaps exist
• Addresses symptoms like visible cracks, gouges, or a warped/loose interior liner

• One refrigerator interior liner

• Disconnect power to the appliance before beginning any repair
• Removal typically requires taking out shelves, trim and fasteners to access the liner
• May require adhesive, clips or screws specific to the model—keep original fasteners and hardware

This support is a replacement mounting bracket that secures internal components and restores proper alignment and stability. Use it when a broken or missing support causes rattling, misalignment, or loose parts. What it does:

• Provides structural support for internal assembly parts to prevent movement or vibration
• Restores proper alignment so doors, drawers, or moving components operate smoothly
• Stops noises and rubbing caused by a cracked or missing bracket
• Helps maintain safe, reliable operation by keeping parts secured

• High-level replacement: remove access panels and fasteners to reach the damaged bracket; mirror steps to reinstall
• Use the same screw locations and hardware as the original; retain mounting screws when removing the old part
• Disconnect power before accessing internal components to reduce shock risk

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This flat replacement glass shelf provides a stable, easy-to-clean surface inside the refrigerator to help organize and protect food. It restores proper shelving where the original glass was cracked, scratched, or missing. What it does:

• Replaces a flat refrigerator shelf glass to support food items and containers
• Restores even storage surfaces and prevents spills from soaking shelves below
• Helps maintain refrigerator interior organization and visibility of contents
• Fits into existing shelf supports or trim rails when the original glass is damaged or removed

• One flat replacement glass shelf

• Handle the glass carefully and wear cut-resistant gloves to avoid injury
• Remove food and any trim/shelf supports before swapping the glass
• Place the new glass into the existing rails or supports; do not force or bend components
• If any clips, rails or seals are damaged, replace them before use to ensure proper fit and safety

This replacement control switch restores a single appliance control function by completing or interrupting the circuit that powers that feature. Fits select Frigidaire appliances to replace a failed or intermittent control switch. What it does:

• Acts as the user/control interface switch that opens or closes power to a specific circuit
• Replaces a worn or failed switch that causes a feature to not respond or work intermittently
• Helps stop unwanted operation when a switch sticks or shorts
• Restores reliable on/off or stepped control for the affected function

• Always disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions before disconnecting
• Require removal of a control panel or access panel; keep screws and small parts organized