Kenmore Range 790.97429901 (79097429901, 790 97429901) Parts

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This flat replacement glass shelf provides a stable, easy-to-clean surface inside the refrigerator to help organize and protect food. It restores proper shelving where the original glass was cracked, scratched, or missing. What it does:

• Replaces a flat refrigerator shelf glass to support food items and containers
• Restores even storage surfaces and prevents spills from soaking shelves below
• Helps maintain refrigerator interior organization and visibility of contents
• Fits into existing shelf supports or trim rails when the original glass is damaged or removed

• One flat replacement glass shelf

• Handle the glass carefully and wear cut-resistant gloves to avoid injury
• Remove food and any trim/shelf supports before swapping the glass
• Place the new glass into the existing rails or supports; do not force or bend components
• If any clips, rails or seals are damaged, replace them before use to ensure proper fit and safety

This replacement control switch restores a single appliance control function by completing or interrupting the circuit that powers that feature. Fits select Frigidaire appliances to replace a failed or intermittent control switch. What it does:

• Acts as the user/control interface switch that opens or closes power to a specific circuit
• Replaces a worn or failed switch that causes a feature to not respond or work intermittently
• Helps stop unwanted operation when a switch sticks or shorts
• Restores reliable on/off or stepped control for the affected function

• Always disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions before disconnecting
• Require removal of a control panel or access panel; keep screws and small parts organized

This insulator is a molded protective cushion that reduces vibration and protects nearby components from wear or contact. It helps keep parts stable and minimizes noise for smoother appliance operation. What it does:

• Cushions components to reduce vibration and rattling
• Protects wiring, tubing, and panels from abrasion and impact
• Helps maintain proper spacing between parts to prevent rubbing
• Can reduce operational noise caused by loose or contacting parts

• One insulator

• Disconnect power to the appliance before starting any repair
• Remove the access panel(s) needed to reach the mounting area; retain fasteners
• Press or slide the insulator into the correct position; it fits snugly and secures the component
• If removal requires cutting old adhesive or clips, replace with equivalent fasteners or adhesives approved by the manufacturer

This multi-connector wire harness restores electrical connections between appliance components so controls and features receive power and signals. Replacing a damaged harness helps stop intermittent operation and restore reliable function. What it does:

• Routes power and signal connections between control boards, switches, and components
• Replaces cracked, burned, or frayed wiring that can cause intermittent or no operation
• Fixes symptoms such as controls not responding, lights or displays failing, or specific functions not working
• Provides factory-style connectors for a direct plug-in replacement

• Disconnect power (unplug or shut off breaker) before starting any repair
• Match connector shapes and pin counts; do not force connectors together
• Secure harness away from hot or moving parts and use existing clips or fasteners

This is a replacement Simmer Select push button for stove/oven control panels. It restores the Simmer Select control's functionality and appearance so the range responds correctly and looks like new. What it does:

• Serves as the user-facing push button for the Simmer Select function on the control panel
• Allows selection of simmer cooking setting when the control switch behind the button is engaged
• Replaces cracked, faded, or missing buttons that stick or fail to make contact
• Helps resolve symptoms such as an unresponsive Simmer Select control, broken button cap, or cosmetic damage

• Disconnect power to the appliance before starting any repair
• Remove the control panel or console to access the button
• Install by snapping the button onto the corresponding control shaft; do not force or bend plastic retainers
• Verify proper operation before reassembling; keep small parts and fasteners secure

This insulation cabinet liner pad restores thermal protection inside the refrigerator cabinet to help maintain consistent temperatures and improve cooling efficiency. Replaces torn or missing insulation behind liners and panels. What it does:

• Provides thermal barrier between inner liner and outer cabinet to help retain cold air
• Reduces frost build-up and moisture migration inside refrigerator walls
• Helps compressor run less frequently by improving overall insulation
• Common symptom: uneven cooling, warm spots, or excessive frost between walls

• Disconnect power to the appliance before starting any repair
• Remove shelves, drawers and interior panels to access the insulation area
• Handle insulation gently; position or trim as needed to fit original cavity
• Use appropriate fasteners or adhesive where original attachment points are present; follow OEM diagrams if available