Kenmore Refrigerator 795.79379901 (79579379901, 795 79379901) Parts

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This door gasket assembly is the appliance door seal that helps keep cold air inside the refrigerator, improving cooling efficiency and reducing frost and moisture buildup around the door. What it does:

• Creates an airtight seal around the refrigerator door to help maintain proper internal temperature.
• Helps reduce energy use and prevents warm air from entering the cabinet.
• Commonly replaced when you notice warm spots, excessive frost, visible gaps, or moisture between door and cabinet.
• Restores proper door sealing to help preserve food freshness and prevent compressor overwork.

• Disconnect power to the appliance before starting any repairs.
• Remove the old gasket and clean the gasket channel before installing the new seal.
• Press and align the new gasket into the channel, ensuring the magnetic/edge flange seats fully around the door.
• After installation, close the door and check for uniform contact; allow the gasket to settle before final testing.

A replacement glass refrigerator shelf that provides a sturdy, easy-to-clean surface for storing food and containers. Restores lost storage space and helps keep items organized and visible. What it does:

• Supports food, containers and small appliances inside the refrigerator
• Creates a flat, stable storage surface for better organization
• Helps contain spills on a single surface for easier cleanup
• Restores damaged, cracked or missing shelving to regain full shelving capacity

• One glass shelf

• Handle glass carefully and wear cut-resistant gloves to prevent injury
• Remove food and other items from adjacent shelves before installing
• Slide into existing shelf tracks or clips until fully seated; do not force
• If shelf hardware is damaged or missing, replace mounting clips or supports before use

This supporter is a small support bracket that stabilizes internal components and helps keep them aligned for reliable operation. It reduces movement and can help prevent excess vibration or rubbing noises. What it does:

• Provides structural support for adjacent components and assemblies
• Helps maintain proper alignment to prevent binding or uneven wear
• Can reduce vibration-related noise when the original support is damaged
• Restores correct spacing to prevent parts from rubbing or scraping

• Disconnect power (and water, if applicable) before servicing to avoid shock or injury.
• Remove the necessary access panels to reach the mounting location; keep track of fasteners.
• Inspect surrounding components and replace any damaged clips or screws for a secure fit.

This door basket is a refrigerator door shelf that restores storage space and secures bottles, jars and small items on the door. It replaces a cracked, broken or missing door bin so items stay organized and easy to reach. What it does

• Holds bottles, condiments and other small food items on the refrigerator door
• Replaces cracked, warped or damaged door shelf that no longer secures items
• Restores usable door storage to reduce shifting or spills during normal use
• Helps maintain proper organization and access to frequently used items

• One door basket

• High-level swap: remove the old bin by lifting or unclipping, then seat the new basket into the door rails until it locks in place
• Check door rail alignment and clean mounting area before installing
• Handle with care to avoid cracking the new plastic during installation
• Disconnect power only if working near electrical components; this is a non-electrical replacement

The Toe Grille Clip is an OEM part for LG refrigerators. This part secures the toe grille to the base of the refrigerator, ensuring it remains in place while providing easy access for cleaning and maintenance. 

Causes of a bad Toe Grille Clip can include breakage due to accidental impacts during cleaning or general wear and tear over time. 

Symptoms of a faulty Toe Grille Clip include:

• The toe grille coming loose or falling off
• Difficulty attaching or detaching the grille for routine maintenance
• Visible damage or deformation of the clip
• Unusual gaps between the grille and the refrigerator base

This OEM LG part is also compatible with some Kenmore models.

This rail guide assembly supports and guides a refrigerator drawer so it slides smoothly and stays aligned. Replace a cracked or worn rail to restore easy opening/closing and keep the drawer from jumping off its track.

• Provides the sliding track and side support for one refrigerator drawer/pan
• Restores smooth movement and proper alignment of the drawer
• Can help resolve sticking, binding, tilting, or the drawer popping off the track
• Often needed when the rail is cracked, stop tab breaks, or wear causes rough travel

• Disconnect power and empty the affected drawer before service
• Remove the drawer (and any shelf above) for clear access; note the original side/orientation
• Release locking tabs or remove mounting screws to swap the rail; secure the new assembly in the same positions
• Reinstall the drawer and test for smooth travel before reloading

This rail guide assembly supports and steers a refrigerator drawer along its track. Replacing a worn or broken guide restores smooth sliding and proper alignment, helping prevent binding and damage to bins and rails.

• Guides the drawer as it opens and closes for smooth movement
• Helps keep the drawer level and properly aligned on the track
• Restores easy operation when the rail is cracked, worn, or deformed
• Typical symptoms: drawer hard to slide, tilts or drops, scraping/grinding noises, visible damage to the rail

• Disconnect power and empty the affected drawer before servicing
• Remove the drawer/bin and any screws or locking tabs securing the old guide
• Transfer any reusable clips or end caps from the old guide to the new assembly if present
• Reinstall, ensure proper engagement on the track, and test for smooth operation

This replacement shutter knob snaps onto the refrigerator's vent lever and gives you fingertip control of the air shutter. Restores smooth, accurate vent adjustment so you can fine-tune airflow to the intended compartment.

• Attaches to the shutter/vent lever on a drawer or shelf cover
• Provides manual open/close control of the air passage
• May help fix: broken or missing knob, slider won't engage, vent stuck in one position, hard to adjust temperature in that compartment
• Durable OEM design for a precise, secure fit

• Unplug the refrigerator before servicing
• Remove the drawer or cover if needed for access to the vent lever
• Pull the damaged knob straight off; align the new knob with the keyed lever and press to seat
• Cycle the slider to confirm the shutter opens and closes smoothly before reassembling

This door basket is a replacement refrigerator door bin that restores inside-door storage for bottles, jars and small containers. It helps keep foods organized and prevents items from shifting or falling when the door opens. What it does:

• Provides a secure shelf on the interior door for bottles, condiments and other small items
• Replaces cracked, broken or missing door storage to restore usable space
• Helps reduce shifting and spillage when opening and closing the refrigerator door
• Matches OEM fit and mounting points for straightforward replacement when correct part number is used

• One replacement door basket

• Inspect mounting pegs or tracks on the door for damage before installing
• Align the basket tabs with the door slots and snap into place until fully seated
• Use only the exact replacement part number to ensure proper fit

This glass shelf replaces a damaged or missing interior refrigerator shelf to restore usable storage and stable support for food and containers. It installs inside the fridge cabinet on existing shelf supports for everyday use. What it does:

• Provides a flat, stable surface for storing food, containers and small appliances
• Replaces cracked, chipped or missing shelves that cause items to tip or fall
• Helps restore proper organization and usable storage space in the refrigerator
• Fits into existing track or support ledges to sit securely in place

• Remove food and any items from the area before installing
• Lift and set the shelf into the cabinet supports; use both hands to avoid dropping
• Wear cut-resistant gloves when handling broken or sharp glass
• If shelf does not seat securely, stop and verify correct shelf position