Kenmore Washer 796.29272000 (79629272000, 796 29272000) Parts

This replacement holder is a small mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts sit firmly and operate as intended. Ideal when a cracked or worn holder causes instability. What it does

• Secures internal components or assemblies to prevent movement or vibration
• Restores proper alignment when a damaged holder allows parts to sag or shift
• Helps reduce noise from loose or unsecured components
• Commonly replaced when the original holder is cracked, broken, or missing

• Turn off and unplug the appliance before beginning any repair.
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit.
• Use appropriate hand tools; avoid forcing parts to prevent further breakage.

This detergent box is the molded dispenser drawer that holds and releases liquid or powdered detergent into the wash tub during cycles, helping ensure detergent is delivered where needed for cleaning. What it does:

• Holds liquid or powdered detergent and channels it into the washer during the fill and wash cycles
• Helps prevent detergent from spilling into the cabinet or away from the wash water
• Common symptom of failure: detergent leaks, fails to dispense, or sits in the drawer instead of flowing into the tub

• One detergent box (dispenser drawer) as shown

• Remove power and water connections before accessing the dispenser area
• Inspect surrounding seals and mounting tabs; replace if damaged to ensure a proper fit
• Clean the dispenser area and rinse with water before installing the new box to remove residue

This bracket assembly secures internal components to the appliance frame, restoring stable support and alignment for panels or assemblies. Replacing a damaged bracket helps stop rattling and prevents misalignment that can affect operation. What it does:

• Provides a secure mounting point for panels, control boards, or internal assemblies
• Restores proper alignment to reduce vibration, noise, or rubbing parts
• Prevents loose components that can cause intermittent contact or wear
• Re-establishes structural support after impact, corrosion, or bracket failure

• One bracket assembly

• Verify power is disconnected before starting any repair
• Inspect mounting screws and adjacent parts; replace any damaged fasteners
• Tighten to manufacturer torque where specified and confirm proper alignment

This bracket assembly secures and supports internal appliance components, restoring proper alignment and stability to parts that have shifted or come loose. It provides a direct replacement to maintain safe, reliable operation. What it does:

• Provides a sturdy mounting point to keep panels, modules, or assemblies properly positioned
• Helps eliminate rattling, misalignment, or loose component movement
• Restores intended structural support after impact or wear
• Works as a direct-fit replacement to return original fit and function

• One bracket assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Use appropriate tools and keep fasteners for a secure fit; replace damaged screws as needed
• Inspect surrounding components and wiring for damage before reassembly

This detergent dispenser box assembly holds and delivers liquid or powdered detergent to the wash chamber, restoring proper dispensing when the original detergent drawer is cracked, clogged, or leaking. Designed as a direct replacement assembly for compatible LG front-load washers. What it does:

• Houses the detergent and fabric softener compartments and channels solutions into the washer at the correct time.
• Restores proper flow when the original dispenser is cracked, warped, or blocked.
• Helps prevent detergent leaks that can cause residue build-up on the door or front panel.
• Compatible with automatic dispensing cycles so detergents are released during the correct wash phase.

• One complete detergent dispenser box assembly as shown.

• High-level replacement: usually accessible from the washer front; remove the front access panel or drawer trim as required.
• Disconnect power and water supply before beginning service to avoid shock or unintended operation.
• Inspect surrounding seals and cabinet for damage; replace any cracked clips or hoses as needed.

This inner tub hub connects the washer's inner drum to the drive assembly, providing a secure rotational link so the drum can spin properly. Replacing a damaged hub restores drum stability and reduces noise or wobbling. What it does:

• Secures the inner tub to the drive shaft so the drum turns with the motor
• Prevents excessive movement, vibration, and scraping noises caused by a worn or broken hub
• Helps correct spin-related issues like uneven spinning or the drum not engaging
• Works with the tub assembly and other drive components to maintain proper drum alignment

• One inner tub hub

• Disconnect power and water supply, and fully drain the washer before starting
• Replacement generally requires removing the outer tub/inner tub assembly and transferring seals or gaskets as needed
• Use proper tools and follow OEM service instructions
• Inspect surrounding components (seals, bearings, suspension) and replace if worn to prevent repeat failure

This softener cap seals the fabric softener dispenser and helps direct liquid into the washer during the rinse cycle, preventing leaks and ensuring the dispenser empties properly. Simple replacement restores proper softener flow. What it does:

• Replaces a cracked, warped, or missing cap that can cause dispenser leaks or slow draining
• Helps channel fabric softener into the tub at the correct cycle instead of spilling into the washer
• Prevents dispenser area buildup and reduces drips that can stain clothing or the washer
• Matches OEM form to fit the factory dispenser housing

• One softener cap

• Turn off and unplug the washer before accessing the dispenser assembly
• Remove the dispenser drawer per your model's service instructions to access the cap
• Inspect surrounding dispenser components and seals; replace any damaged parts for best performance

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

This holder is a small mounting bracket that secures internal components in place, helping prevent movement and vibration for reliable operation. It's a simple replacement part that restores proper fit and stability. What it does:

• Secures and supports nearby components or assemblies to prevent shifting
• Reduces vibration and rattling that can cause noise or wear
• Helps maintain correct alignment for connected parts to operate smoothly
• Restores original component retention after damage or loss of the bracket

• Disconnect power to the appliance before beginning any repair
• Basic hand tools may be required; handle small parts carefully to avoid loss
• Inspect surrounding clips and fasteners; replace any that are damaged

This detergent box is the replacement drawer housing that holds and directs liquid or powder detergent in the washer's dispenser assembly, restoring proper detergent flow and minimizing leaks or dispenser clogs. What it does

• Replaces a damaged or cracked detergent drawer housing to stop leaks and contain detergent.
• Directs liquid and powder detergent into the wash chamber for normal dispensing.
• Helps prevent detergent buildup and improves dispenser drainage when functioning correctly.
• Commonly replaced when the drawer is broken, warped, or no longer seats properly.

• Disconnect power and water supply to the appliance before starting any repair.
• Remove the dispenser assembly to access and replace the box.
• Handle plastic parts carefully to avoid cracking; use proper tools and follow OEM alignment tabs when installing.

This heater assembly replaces the dryer's heating element and housing to restore warm airflow for drying cycles. It's a direct-replacement assembly that re-establishes the appliance's heat source when the dryer won't heat properly. What it does:

• Houses the electric heating element that produces heat for drying cycles
• Replaces a burned-out element, open circuit, or damaged housing that can stop the dryer from heating
• Helps resolve symptoms such as no heat, only air tumbling, or weak/partial heating
• Works with the dryer's blower and thermostat to deliver consistent drying temperatures

• One heater assembly (heating element installed in housing)

• Disconnect power to the dryer (unplug or shut off breaker) before servicing
• Allow components to cool and wear gloves to protect hands from sharp edges
• Verify the part number matches the dryer's parts list before installation